Siemens SINAMICS G120 - Page 541

SINAMICS G120 Control Units CU240B-2/CU240E-2
List Manual (LH11), 01/2016, A5E33839529
541
2 Parameters
2.4 BICO parameters (connectors/binectors)
p1502[0...n] BI: Freeze moment of inertia estimator / J_estim freeze
p2080[0...15] BI: Binector-connector converter status word 1 / Bin/con ZSW1
p2081[0...15] BI: Binector-connector converter status word 2 / Bin/con ZSW2
p2082[0...15] BI: Binector-connector converter status word 3 / Bin/con ZSW3
p2083[0...15] BI: Binector-connector converter status word 4 / Bin/con ZSW4
p2084[0...15] BI: Binector-connector converter status word 5 / Bin/con ZSW5
p2103[0...n] BI: 1st acknowledge faults / 1st acknowledge
p2104[0...n] BI: 2nd acknowledge faults / 2nd acknowledge
p2105[0...n] BI: 3rd acknowledge faults / 3rd acknowledge
p2106[0...n] BI: External fault 1 / External fault 1
p2107[0...n] BI: External fault 2 / External fault 2
p2108[0...n] BI: External fault 3 / External fault 3
p2112[0...n] BI: External alarm 1 / External alarm 1
p2116[0...n] BI: External alarm 2 / External alarm 2
p2117[0...n] BI: External alarm 3 / External alarm 3
p2144[0...n] BI: Motor stall monitoring enable (negated) / Mot stall enab neg
p2148[0...n] BI: RFG active / RFG active
p2200[0...n] BI: Technology controller enable / Tec_ctrl enable
p2220[0...n] BI: Technology controller fixed value selection bit 0 / Tec_ctrl sel bit 0
p2221[0...n] BI: Technology controller fixed value selection bit 1 / Tec_ctrl sel bit 1
p2222[0...n] BI: Technology controller fixed value selection bit 2 / Tec_ctrl sel bit 2
p2223[0...n] BI: Technology controller fixed value selection bit 3 / Tec_ctrl sel bit 3
p2235[0...n] BI: Technology controller motorized potentiometer raise setpoint / Tec_ctrl mop raise
p2236[0...n] BI: Technology controller motorized potentiometer lower setpoint / Tec_ctrl mop lower
p2286[0...n] BI: Hold technology controller integrator / Tec_ctr integ hold
p2290[0...n] BI: Technology controller limiting enable / Tec_ctrl lim enab
p3111[0...n] BI: External fault 3 enable / Ext fault 3 enab
p3112[0...n] BI: External fault 3 enable negated / Ext flt 3 enab neg
p3232[0...n] BI: Load monitoring failure detection / Load_moni fail_det
p3330[0...n] BI: 2/3 wire control command 1 / 2/3 wire cmd 1
p3331[0...n] BI: 2/3 wire control command 2 / 2/3 wire cmd 2
p3332[0...n] BI: 2/3 wire control command 3 / 2/3 wire cmd 3
p5614 BI: Pe set switching-on inhibited signal source / Pe sw on_inh s_src
p8542[0...15] BI: Active STW1 in the BOP/IOP manual mode / STW1 act OP
p8558 BI: Select IOP manual mode / Sel IOP man mode
p9705 BI: SI Motion: Test stop signal source / SI Mtn test stop
p20030[0...3] BI: AND 0 inputs / AND 0 inputs
p20034[0...3] BI: AND 1 inputs / AND 1 inputs
p20038[0...3] BI: AND 2 inputs / AND 2 inputs
p20042[0...3] BI: AND 3 inputs / AND 3 inputs
p20046[0...3] BI: OR 0 inputs / OR 0 inputs
p20050[0...3] BI: OR 1 inputs / OR 1 inputs
p20054[0...3] BI: OR 2 inputs / OR 2 inputs
p20058[0...3] BI: OR 3 inputs / OR 3 inputs
p20062[0...3] BI: XOR 0 inputs / XOR 0 inputs
p20066[0...3] BI: XOR 1 inputs / XOR 1 inputs
p20070[0...3] BI: XOR 2 inputs / XOR 2 inputs
p20074[0...3] BI: XOR 3 inputs / XOR 3 inputs
p20078 BI: NOT 0 input I / NOT 0 input I
p20082 BI: NOT 1 input I / NOT 1 input I
p20086 BI: NOT 2 input I / NOT 2 input I
p20090 BI: NOT 3 input I / NOT 3 input I
p20138 BI: MFP 0 input pulse I / MFP 0 inp_pulse I
p20143 BI: MFP 1 input pulse I / MFP 1 inp_pulse I
p20148 BI: PCL 0 input pulse I / PCL 0 inp_pulse I