Mitutoyo SURFTEST SJ-410 - Styli and Nosepiece

No. 99MBB765A
22-12
22.9.2 Styli and nosepiece
Various styli and skid-attached nosepiece are provided. Use appropriate ones according
to workpieces, referring to the combination and application stated in the table.
Skidless nosepiece
Application
－
－
Hole dia:
Φ2 mm (Φ0.078 in) or more
Hole depth: 15 mm (0.590 in) or less
Hole dia:
Φ1.6 mm (Φ0.062 in) or more
Hole depth: 8 mm (0
.314 in) or less
Hole dia:
Φ1.2 mm (Φ0.047 in) or more
Hole depth: 8 mm (0.314 in) or less
Groove depth: 30 mm (1.181 in) or less
Groove depth: 20 mm (0.787 in) or less
Groove depth: 10 mm (0.393 in) or less
Groove depth: 10 mm (0.393 in) or less
R-surface, cylindrical surface, spherical surface measurement
Curved surface measurement
－
Corner surface
Pin Sharp edge
Surface can be reached only from the side
－
－
No. and name
12AAB355
Standard
nosepiece
(Standard
accessory)
Nosepiece with a skid
Application
－
Φ2 to Φ20
Hole dia:
Φ4 mm
(Φ0.157 in) or more Hole depth: 15 mm (0.590 in) or less
Hole dia:
Φ2.3 mm
(Φ0.090 in) or more Hole depth: 8 mm (0.314 in) or less
－
－
Groove width: 9.5 mm (0.374 in) or more Groove depth: 20 mm (0.787 in) or less
Groove width: 9.5 mm (0.374 in) or more Groove depth: 10 mm (0.393 in) or less
R-surface, cylindrical surface, spherical surface measurement
Curved surface measurement
－
Corner surface
Pin Sharp edge
－
－
－
Name
Standard nosepiece
Cylindrical surface nosepiece
Small hole nosepiece
Ultra-small hole nosepiece
－
－
Deep groove (20 mm/0.787 in) nosepiece
Deep groove (10 mm/0.393 in) nosepiece
Narrow groove nosepiece
R-surface nosepiece
Seesaw type nosepiece
－
Corner surface nosepiece
Knife edge surface nosepiece
－
－
－
No.
12AAB344
12AAB345
12AAB346
12AAB347
－
－
12AAB348
12AAB349
12AAB350
12AAB351
12AAB352
－
12AAB353
12AAB354
－
－
－
Tip shape
Angle
60° 90° 90°
60° 90° 90°
60° 90° 90°
60° 90° 90°
60° 90° 90°
60° 90° 90°
60° 90° 90°
60° 90° 90°
60° 90° 90°
60° 90° 90°
60° 90° 90°
60° 90° 90°
Radius
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
2 µm (78.740 µin) 5 µm (196.850 µin) 10 µm (393.700 µin)
Stylus
Name
Standard
stylus
Standard stylus Standard stylus
Small hole stylus Small hole stylus Small hole stylus
Ultra-small hole stylus Ultra-small hole stylus Ultra-small hole stylus
Ultra-small hole stylus Ultra-small hole stylus Ultra-small hole stylus
Deep groove (30 mm/
1.181 in) stylus
Deep groove (30 mm/1.181 in) stylus Deep groove (30 mm/1.181 in) stylus
Deep groove (20 mm/0.787 in) stylus Deep groove (20 mm/0.787 in) stylus Deep groove (20 mm/0.787 in) stylus
Deep groove (10 mm/0.393 in) stylus Deep groove (10
mm/0.393 in) stylus
Deep groove (10 mm/0.393 in) stylus
Rolling circle waviness stylus
Gear tooth surface stylus
Knife edge surface stylus
L-shape stylus
Deep hole 2X stylus
Deep hole 3X stylus
No.
12AAC731 12AAB403 12AAB415
12AAC732 12AAB404 12AAB416
12AAC733 12AAB405 12AAB417
12AAC734 12AAB406 12AAB418
*12AAC737 *12AAB407 *12AAB419
*12AAC736 *12AAB408 *12AAB420
12AAC735 12AAB409 12AAB421
12AAB338
12AAB339 12AAB410 12AAB422
12AAC738 12AAB411 12AAB423
*12AAC739 *12AAB412 *12AAB424
*12AAC740 *12AAB413 *12AAB425
*12AAC741 *12AAB414 *12AAB426
Assessed item
Standard
Cylinder
Small hole
Extra-small hole
Ultra-small hole
Deep groove
Narrow groove
Round surface
Curved surface measurement
Rolling circle waviness
Gear tooth surface Corner surface
Knife edge Measurement
Off-centered surface
Deep hole
If a stylus with * mark is used, the detector's measuring force will not be covered under
warranty.