Rohde & Schwarz RTP Series - Page 2095

Remote control commands
R&S
®
RTP
2095User Manual 1337.9952.02 ─ 12
●
The sources of the serial bus are channel signals: use BUS<m>:...:SOURce
commands.
●
Decoding is enabled: BUS<m>[:STATe] is set to ON.
There are two commands for each parameter, that you can use for defining the USBPD
settings.
For example, to set the Frame type =Control Frame > Field =MsgID >Data value you
can use one of the following commands:
●
SEARch:TRIGger:USBPD:FRAMe3:FLD3:DMIN 01100
Defines the parameter by using the index <m> for the frame number and <n> for
the field number. For an overview, see Table 22-15.
●
SEARch:TRIGger:USBPD:DMIN "Control", "MsgID", 01100
Defines the parameter by using the frame and field name.
SEARch:TRIGger:USBPd:ERENable............................................................................. 2095
SEARch:TRIGger:USBPd:ERRor<m>:ENABle................................................................2095
SEARch:TRIGger:USBPd:FRENable............................................................................. 2096
SEARch:TRIGger:USBPd:FRAMe<m>:ENABle...............................................................2096
SEARch:TRIGger:USBPd:FIENable...............................................................................2096
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:ENABle..................................................2096
SEARch:TRIGger:USBPd:BIT....................................................................................... 2097
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:BIT........................................................ 2097
SEARch:TRIGger:USBPd:DMAX...................................................................................2097
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:DMAX....................................................2097
SEARch:TRIGger:USBPd:DMIN....................................................................................2098
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:DMIN.....................................................2098
SEARch:TRIGger:USBPd:DOPerator.............................................................................2098
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:DOPerator..............................................2098
SEARch:TRIGger:USBPd:IMAX.................................................................................... 2099
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:IMAX..................................................... 2099
SEARch:TRIGger:USBPd:IMIN..................................................................................... 2099
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:IMIN...................................................... 2099
SEARch:TRIGger:USBPd:IOPerator.............................................................................. 2100
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:IOPerator............................................... 2100
SEARch:TRIGger:USBPd:ERENable <SearchName>,<ErrorName>, <Enabler>
SEARch:TRIGger:USBPd:ERRor<m>:ENABle <SearchName>,<Enable>
SEARch:TRIGger:USBPd:ERRor<m>:ENABle? <SearchName>
Enables or disables the checking condition for searching a specific error in the selected
field of the selected frame.
Suffix:
<m>
.
*
Specifies the error number.
Parameters:
<Enable> ON | OFF
*RST: ON
Protocols