Scanlab RTC6 PCIe Board - Page 311

RTC6 boards
Doc. Rev. 1.0.21 en-US
10 RTC6 Commands
311
innovators for industry
Status Monitoring and Diagnostics
(n_) set_trigger
ds
........................................... 751
(n_) set_trigger4
ds
........................................ 760
(n_) set_trigger8
ds
........................................ 761
Starting and Stopping Lists by External
Control Signals and Master/Slave
Synchronization
(n_) set_control_mode_list
nor
....................... 622
(n_) set_extstartpos_list
us
............................. 637
List Handling and Structured Programming
(n_) list_continue
nor
...................................... 481
(n_) list_jump_pos
us
...................................... 483
(n_) list_jump_rel
us
....................................... 485
(n_) list_next
us
............................................... 487
(n_) list_nop
nor
.............................................. 487
(n_) list_repeat
us
........................................... 488
(n_) list_until
us
.............................................. 490
(n_) long_delay
nor
......................................... 523
(n_) set_end_of_list
nor
.................................. 635
(n_) set_list_jump
us
....................................... 680
(n_) set_wait
nor
............................................. 765
Subroutine Commands
(n_) list_call
us
................................................ 475
(n_) list_call_abs
us
......................................... 477
(n_) list_call_abs_repeat
us
............................ 478
(n_) list_call_repeat
us
.................................... 480
(n_) list_return
us
............................................ 489
(n_) sub_call
us
............................................... 802
(n_) sub_call_abs
us
........................................ 803
(n_) sub_call_abs_repeat
us
........................... 804
(n_) sub_call_repeat
us
................................... 805
Setting the Laser Parameters
(n_) config_laser_signals_list
ds
..................... 343
(n_) set_auto_laser_params_list
ds
................ 617
(n_) set_encoder_speed
ds
............................. 633
(n_) set_firstpulse_killer_list
us
...................... 640
(n_) set_laser_delays
us
.................................. 671
(n_) set_laser_pin_out_list
us
......................... 673
(n_) set_laser_pulses
ds
.................................. 676
(n_) set_laser_timing
ds
................................. 678
(n_) set_pulse_picking_list
us
......................... 719
(n_) set_qswitch_delay_list
us
........................ 719
(n_) set_softstart_level_list
nor
...................... 742
(n_) set_softstart_mode_list
var
..................... 743
(n_) set_standby_list
ds
.................................. 745
(n_) set_vector_control
us
.............................. 762
(n_) spot_distance
us
..................................... 785
Setting the Scanner Parameters
(n_) set_delay_mode_list
mul
......................... 629
(n_) set_jump_speed
us
.................................. 666
(n_) set_mark_speed
ds
.................................. 681
(n_) set_scanner_delays
ds
............................. 732
(n_) set_sky_writing_limit_list
us
................... 735
(n_) set_sky_writing_list
nor
........................... 736
(n_) set_sky_writing_mode_list
nor
............... 738
(n_) set_sky_writing_para_list
nor
.................. 741
Coordinate Transformations
(n_) set_angle_list
var
..................................... 612
(n_) set_defocus_list
var (1)
............................. 625
(n_) set_defocus_offset_list
var (1)
.................. 627
(n_) set_matrix_list
var
.................................... 684
(n_) set_offset_list
var
.................................... 706
(n_) set_offset_xyz_list
var (2)
........................ 708
(n_) set_scale_list
var
...................................... 724
Online Positioning
(n_) apply_mcbsp_list
nor
............................... 327
(n_) set_mcbsp_global_matrix_list
us
........... 686
(n_) set_mcbsp_global_rot_list
us
................ 687
(n_) set_mcbsp_global_x_list
us
................... 688
(n_) set_mcbsp_global_y_list
us
................... 689
(n_) set_mcbsp_matrix_list
us
........................ 694
(n_) set_mcbsp_rot_list
us
.............................. 699
(n_) set_mcbsp_x_list
us
................................. 700
(n_) set_mcbsp_y_list
us
................................. 701
Direct Laser and Scan Head Control
(n_) laser_on_list
var
....................................... 470
(n_) laser_on_pulses_list
var
........................... 471
(n_) laser_signal_off_list
nor
........................... 473
(n_) laser_signal_on_list
nor
........................... 474
(n_) para_laser_on_pulses_list
var
.................. 556
Pixel Output Mode
(n_) set_default_pixel_list
us
.......................... 623
(n_) set_n_pixel
var
......................................... 705
(n_) set_pixel
var
............................................. 711
(n_) set_pixel_line
nor
..................................... 712
(n_) set_pixel_line_3d
mul (2)
.......................... 715
(1) Only with Option “3D”.
(2) Limited functionality if no Option “3D”.