Scanlab RTC6 PCIe Board - Page 313

RTC6 boards
Doc. Rev. 1.0.21 en-US
10 RTC6 Commands
313
innovators for industry
”Fly Extension” List Commands
(n_) activate_fly_1_axis
var
............................ 318
(n_) activate_fly_2_axes
var
........................... 319
(n_) fly_return_1_axis
var
.............................. 388
(n_) fly_return_2_axes
var
............................. 389
(n_) fly_return_3_axes
var
............................. 390
(n_) park_position_1_axis
var
........................ 565
(n_) park_position_2_axes
var
....................... 566
(n_) park_return_1_axis
var
........................... 569
(n_) park_return_2_axes
var
.......................... 570
(n_) set_fly_1_axis
nor
................................... 641
(n_) set_fly_2_axes
nor
.................................. 642
(n_) set_fly_3_axes
mul
.................................. 646
(n_) wait_for_1_axis
nor
................................ 838
(n_) wait_for_2_axes
mul
............................... 840
Controlling Stepper Motors
(n_) stepper_abs_list
us
.................................. 788
(n_) stepper_abs_no_list
us
............................ 789
(n_) stepper_control_list
us
............................ 790
(n_) stepper_enable_list
us
............................ 792
(n_) stepper_rel_list
us
................................... 795
(n_) stepper_rel_no_list
us
............................. 796
(n_) stepper_wait
nor
..................................... 797
Jump Mode
(n_) set_jump_mode_list
nor
.......................... 665
Camming
(n_) camming
nor
............................................ 338
Wobbel Mode
(n_) set_wobbel
ds
......................................... 766
(n_) set_wobbel_control
us
............................ 768
(n_) set_wobbel_direction
us
......................... 770
(n_) set_wobbel_mode
ds
.............................. 771
(n_) set_wobbel_mode_phase
ds
................... 774
(n_) set_wobbel_offset
ds
.............................. 775
(n_) set_wobbel_vector
us
............................. 776
(n_) set_wobbel_vector_2
us
.......................... 780
List Commands only for Scan Systems with
SCANahead Control
(n_) activate_scanahead_autodelays_list
us
.. 325
(n_) set_scanahead_laser_shifts_list
us
......... 725
(n_) set_scanahead_line_params_list
us
........ 727
List Commands for a Restricted User Group
only
(1)
(n_) regulation3
nor
........................................ 590
(n_) set_duty_cycle_table
nor
......................... 631
(n_) set_laser_timing_table
nor
...................... 679
Other List Commands
(n_) jump_abs_drill
nor
................................... 467
(n_) jump_abs_drill_2
nor
............................... 467
(n_) jump_rel_drill
nor
.................................... 469
(n_) jump_rel_drill_2
nor
................................. 469
(n_) range_checking
us
................................... 575
(n_) save_and_restart_timer
ds
...................... 599
(n_) set_mcbsp_out_oie_list
us
...................... 780
(n_) set_zoom_list
us
...................................... 780
(n_) store_timestamp_counter_list
us
........... 801
(n_) wait_for_timestamp_counter
nor
........... 848
(n_) wait_for_timestamp_counter_long
nor
.. 849
(n_) wait_for_timestamp_counter_mode
nor
850
(1) These users have been informed separately in how to
handle these RTC6 commands. Therefore, only the
command table is available in this manual and further
information is omitted.