Fuji Xerox DocuCentre SC2020 Service Manual

05/2014
2-61
DC SC2020
Troubleshooting
CHAIN 35
Version 1.1
035-701 Send T1 Time Out
BSD-ON:-
In send, T1 timeout.
Cause/Action
Recover after the [OK] or [Close] button is pressed or message is displayed for specified time. -Checking
the telephone line connection. Reconnect the telephone line connector. -Checking the sending side fax.
Receive the fax data from known good fax machine. -Update to the latest F/W. If the error persists after
the action above is taken, ensure that the error replicates after the printer is powered off and then on, and
then replace the following parts in sequence.
• FAX PWB (PL 18.5)
• ESS PWB (PL 18.2)
035-702 Receive DCN
BSD-ON:-
DCN receive.
Cause/Action
Recover after the [OK] or [Close] button is pressed or message is displayed for specified time. -Checking
the telephone line connection. Reconnect the telephone line connector. -Checking the sending side fax.
Receive the fax data from known good fax machine. -Update to the latest F/W. If the error persists after
the action above is taken, ensure that the error replicates after the printer is powered off and then on, and
then replace the following parts in sequence.
• FAX PWB (PL 18.5)
• ESS PWB (PL 18.2)
035-704 Not Send Ability
BSD-ON:-
Remote device has no ability to send.
Cause/Action
Recover after the [OK] or [Close] button is pressed or message is displayed for specified time. -Checking
the telephone line connection. Reconnect the telephone line connector. -Checking the sending side fax.
Receive the fax data from known good fax machine. -Update to the latest F/W. If the error persists after
the action above is taken, ensure that the error replicates after the printer is powered off and then on, and
then replace the following parts in sequence.
• FAX PWB (PL 18.5)
• ESS PWB (PL 18.2)
035-705 DCS/NSS Resend Over
BSD-ON:-
DCS/NSS resend over.
Cause/Action
Recover after the [OK] or [Close] button is pressed or message is displayed for specified time. -Checking
the telephone line connection. Reconnect the telephone line connector. -Checking the sending side fax.
Receive the fax data from known good fax machine. -Update to the latest F/W. If the error persists after
the action above is taken, ensure that the error replicates after the printer is powered off and then on, and
then replace the following parts in sequence.
• FAX PWB (PL 18.5)
• ESS PWB (PL 18.2)
035-706 Fall Back Error
BSD-ON:-
Fall back error.
Cause/Action
Recover after the [OK] or [Close] button is pressed or message is displayed for specified time. -Checking
the telephone line connection. Reconnect the telephone line connector. -Checking the sending side fax.
Receive the fax data from known good fax machine. -Update to the latest F/W. If the error persists after
the action above is taken, ensure that the error replicates after the printer is powered off and then on, and
then replace the following parts in sequence.
• FAX PWB (PL 18.5)
• ESS PWB (PL 18.2)
035-708 Post Message Resend Over
BSD-ON:-
Post message resend over.
Cause/Action
Recover after the [OK] or [Close] button is pressed or message is displayed for specified time. -Checking
the telephone line connection. Reconnect the telephone line connector. -Checking the sending side fax.
Receive the fax data from known good fax machine. -Update to the latest F/W. If the error persists after
the action above is taken, ensure that the error replicates after the printer is powered off and then on, and
then replace the following parts in sequence.
• FAX PWB (PL 18.5)
• ESS PWB (PL 18.2)

Fuji Xerox DocuCentre SC2020 Specifications

General

Brand	Fuji Xerox
Model	DocuCentre SC2020
Category	All in One Printer
Language	English