EasyManuals Logo

STMicroelectronics STM32WL5 Series User Manual

STMicroelectronics STM32WL5 Series
1450 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1331 background imageLoading...
Page #1331 background image
RM0453 Rev 5 1331/1450
RM0453 Debug support (DBG)
1435
The address of the AP registers is composed as follows:
Bits [7:4]: content of the APBANKSEL[3:0] field in the DP_SELECTR register
(see Section 38.4.8)
Bits [3:2]: content of the A(3:2) field of the APACC data register in the JTAG-DP
(see Table 268: DP register map and reset values) or of the SW-DP packet request
(see Table 264: Packet request), depending on the debug interface used
Bits [1:0]: always set to 0
The content of the APSEL[3:0] field of the DP_SELECTR register defines which MEM-AP is
being accessed.
Table 269. MEM-AP registers
Address APBANKSEL A(3:2) Name Description
0x00 0x0 0 AP_CSWR Control/status word register (see Section 38.5.1)
0x04 0x0 1 AP_TAR
Transfer address register (see Section 38.5.2)
Target address for the bus transaction
0x08 - - - Reserved
0x0C 0x0 3 AP_DRWR
Data read/write register (see Section 38.5.3)
Access to this register triggers a corresponding transaction on
the debug bus to the address in AP_TAR[31:0].
0x10 0x1 0 AP_BD0R
Banked data 0 register (see Section 38.5.4)
Access to this register triggers a corresponding transaction on
the debug bus to the address in Address [31:4] = AP_TAR[31:4],
address [3:0] = 0x0.
0x14 0x1 1 AP_BD1R
Banked data 1 register (see Section 38.5.4)
Access to this register triggers a corresponding transaction on
the debug bus to the address in Address [31:4] = AP_TAR[31:4],
address [3:0] = 0x4.
0x18 0x1 2 AP_BD2R
Banked data 2 register (see Section 38.5.4)
Access to this register triggers a corresponding transaction on
the debug bus to the address in Address [31:4] = AP_TAR[31:4],
address [3:0] = 0x8.
0x1C 0x1 3 AP_BD3R
Banked data 3 register (see Section 38.5.4)
Access to this register triggers a corresponding transaction on
the debug bus to the address in Address [31:4] = AP_TAR[31:4],
address [3:0] = 0xC.
0x20 - - - Reserved
0x24 to
0xEC
- - - Reserved
0xF0 - - - Reserved
0xF4 - - - Reserved
0xF8 0xF 2 AP_BASER
Debug base address register (RO) (see Section 38.5.5)
Base address of the ROM table
0xFC 0xF 3 AP_IDR Identification register (RO) (see Section 38.5.6)

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the STMicroelectronics STM32WL5 Series and is the answer not in the manual?

STMicroelectronics STM32WL5 Series Specifications

General IconGeneral
BrandSTMicroelectronics
ModelSTM32WL5 Series
CategoryMicrocontrollers
LanguageEnglish

Related product manuals