397
10.2 Error codes and countermeasures
Chapter 10
Error code Displayed message Problems/countermeasures
G2500U
[Device name] There is an internal device error.
Restart the AeroDR Interface Unit/AeroDR Interface
Unit2.
System error of the corresponding device occurred.
Restart the corresponding device.
G2501U
[Device name] There is an internal device error or a
communication error. Contact a service representa-
tive.
Contact Konica Minolta technical representatives.
G410**
[Device name] Exposure switch is not released. Re-
lease the exposure switch.
Release the exposure switch.
G4103U
[Device name] Exposure link failed, X-rays are not
exposed. Please take exposure once again.
X-rays were not irradiated. Try performing the expo-
sure again.
The release of the exposure switch may occur quickly,
so exposure while making sure to release the expo-
sure switch properly.
10.2.5 AeroDR Stitching System errors
Error codes starting with "S" are indicating AeroDR Stitching System errors.
Error code Displayed message Problems/countermeasures
S000**
S00100
[AeroDR Stitching Unit name] MCB Error
Contact a service representative.
Contact Konica Minolta technical representatives.
S00110
S00120
[AeroDR Stitching Unit name] Motor Error
Please power OFF of AeroDR Stitching unit.
Please confirm the auto barrier unit movement area
before switch the power to ON.
(1) Turn o the AeroDR Stitching System.
(2) Check that there are no obstacles in the operat-
ing range of the Stitching Mask of the AeroDR
Stitching X-Ray Auto-barrier Unit, and turn on the
AeroDR Stitching System.
S00130
[AeroDR Stitching Unit name] MCB Error
Contact a service representative.
Contact Konica Minolta technical representatives.
S00140
[AeroDR Stitching Unit name] Motor Error
Please power OFF of AeroDR Stitching unit.
Please confirm the auto barrier unit movement area
before switch the power to ON.
(1) Turn o the AeroDR Stitching System.
(2) Check that there are no obstacles in the operat-
ing range of the Stitching Mask of the AeroDR
Stitching X-Ray Auto-barrier Unit, and turn on the
AeroDR Stitching System.
S00200
[AeroDR Stitching Unit name] Motor Error
Please power OFF/ON of AeroDR Stitching unit.
Restart the AeroDR Stitching System.
S00210
S00220
[AeroDR Stitching Unit name] Motor Error
Please power OFF of AeroDR Stitching unit.
Please confirm the auto barrier unit movement area
before switch the power to ON.
(1) Turn o the AeroDR Stitching System.
(2) Check that there are no obstacles in the operat-
ing range of the Stitching Mask of the AeroDR
Stitching X-Ray Auto-barrier Unit, and turn on the
AeroDR Stitching System.
S00230
[AeroDR Stitching Unit name] Sensor Error
Please power OFF/ON of AeroDR Stitching unit.
Restart the AeroDR Stitching System.
S00240
[AeroDR Stitching Unit name] Motor Error
Please power OFF of AeroDR Stitching unit.
Please confirm the auto barrier unit movement area
before switch the power to ON.
(1) Turn o the AeroDR Stitching System.
(2) Check that there are no obstacles in the operat-
ing range of the Stitching Mask of the AeroDR
Stitching X-Ray Auto-barrier Unit, and turn on the
AeroDR Stitching System.
S00250
[AeroDR Stitching Unit name] Motor Error
Please power OFF/ON of AeroDR Stitching unit.
Restart the AeroDR Stitching System.
S00260
[AeroDR Stitching Unit name] Sensor Error
Please power OFF/ON of AeroDR Stitching unit.
S00400
[AeroDR Stitching Unit name] MCB Error
Contact a service representative.
Contact Konica Minolta technical representatives.
S00420
[AeroDR Stitching Unit name] Motor Error
Please power OFF/ON of AeroDR Stitching unit.
Restart the AeroDR Stitching System.
S00510
S00530
[AeroDR Stitching Unit name] Sensor Error
Contact a service representative.
Contact Konica Minolta technical representatives.
Continued on the next page
To Next Page
Loading...
