Siemens SINAMICS G120XA - Page 895

parabolic, 276, 285
square-law, 276, 285
CI: Active speed setpoint in the BOP/IOP manual
mode
p8543, 681
CI: Comm IF USS PZD send word
p2016[0...3], 555
CI: Connector-binector converter signal source
p2099[0...1], 576
CI: CU analog outputs signal source
p0771[0...2], 436
CI: Current limit, variable
p0641[0...n], 425
CI: ESM setpoint technology controller
p3884, 655
CI: Free tec_ctrl 0 actual value signal source
p11064, 688
CI: Free tec_ctrl 0 limit maximum signal source
p11097, 691
CI: Free tec_ctrl 0 limit minimum signal source
p11098, 691
CI: Free tec_ctrl 0 limit offset signal source
p11099, 691
CI: Free tec_ctrl 0 setpoint signal source
p11053, 687
CI: Free tec_ctrl 1 actual value signal source
p11164, 695
CI: Free tec_ctrl 1 limit maximum signal source
p11197, 698
CI: Free tec_ctrl 1 limit minimum signal source
p11198, 698
CI: Free tec_ctrl 1 limit offset signal source
p11199, 698
CI: Free tec_ctrl 1 setpoint signal source
p11153, 694
CI: Free tec_ctrl 2 actual value signal source
p11264, 702
CI: Free tec_ctrl 2 limit maximum signal source
p11297, 705
CI: Free tec_ctrl 2 limit minimum signal source
p11298, 705
CI: Free tec_ctrl 2 limit offset signal source
p11299, 705
CI: Free tec_ctrl 2 setpoint signal source
p11253, 701
CI: Load monitoring speed actual value
p3230[0...n], 643
CI: Main setpoint
p1070[0...n], 473
CI: Main setpoint scaling
p1071[0...n], 474
CI: Minimum speed signal source
p1106[0...n], 480
CI: Motorized potentiometer automatic setpoint
p1042[0...n], 470
CI: Motorized potentiometer setting value
p1044[0...n], 470
CI: PROFIdrive PZD send double word
p2061[0...15], 565
CI: PROFIdrive PZD send word
p2051[0...16], 563
CI: Ramp-down scaling input
p29579[0...n], 714
CI: Ramp-function generator ramp-down time scaling
p1139[0...n], 486
CI: Ramp-function generator ramp-up time scaling
p1138[0...n], 485
CI: Ramp-function generator setpoint input
p29643, 721
CI: Ramp-function generator setting value
p1144[0...n], 488
CI: Ramp-up scaling input
p29578[0...n], 713
CI: Skip speed scaling
p1098[0...n], 479
CI: Speed limit in negative direction of rotation
p1088[0...n], 478
CI: Speed limit in positive direction of rotation
p1085[0...n], 477
CI: Speed limit RFG negative direction of rotation
p1052[0...n], 472
CI: Speed limit RFG positive direction of rotation
p1051[0...n], 472
CI: Speed setpoint for messages/signals
p2151[0...n], 590
CI: Supplementary setp
p1075[0...n], 474
CI: Supplementary setpoint scaling
p1076[0...n], 474
CI: Technology controller actual value
p2264[0...n], 613
CI: Technology controller Kp adaptation input value
signal source
p2310, 620
CI: Technology controller Kp adaptation scaling
signal source
p2315, 621
CI: Technology controller limit offset
p2299[0...n], 619
CI: Technology controller maximum limit signal source
p2297[0...n], 618
CI: Technology controller minimum limit signal source
p2298[0...n], 619
Index
SINAMICS G120XA converter
Operating Instructions, 03/2019, FW V1.0, A5E44751205B AB 893