MacDon FFT FlexDraper FD75 - Page 10

TABLE O F CONTENT
S
Locking/Unlocking Header Wings..................................................................................... 64
Operating in Flex Mode................................................................................................... 64
Operating in Rigid Mode .................................................................................................. 65
3.7.3 Header Angle ......................................................................................................................... 66
Controlling He a de r Angle ................................................................................................ 67
3.7.4 Reel Speed ............................................................................................................................ 67
Optional Reel Drive Sprockets......................................................................................... 68
3.7.5 Ground Speed ....................................................................................................................... 68
3.7.6 Draper Speed ........................................................................................................................ 69
Adjusting Side Draper Speed........................................................................................... 70
Adjusting Feed Draper Speed .......................................................................................... 71
3.7.7 Knife Speed........................................................................................................................... 71
Checking Knife Speed..................................................................................................... 72
3.7.8 Reel Height............................................................................................................................ 73
3.7.9 Reel Fore-Aft Position ............................................................................................................ 73
Adjusting Reel Fore-Aft Position ...................................................................................... 74
Repositioning Fore-Aft Cylinders ...................................................................................... 75
3.7.10 Repositioning Fore-Aft Cylinders with Multi-Crop Rapid Reel Conversion Option........................ 78
3.7.11 Reel Tine Pitch....................................................................................................................... 80
Reel Cam Settings.......................................................................................................... 80
Adjusting Reel Cam ........................................................................................................ 82
3.7.12 Crop Dividers......................................................................................................................... 83
Removing Crop Dividers from Header with Latch Option ................................................... 83
Removing Crop Dividers from Header without Latch Option............................................... 84
Installing Cro p Dividers on Header with Latch Option ........................................................ 84
Installing C ro p Dividers on Header without Latch Op tio n.................................................... 86
3.7.13 Crop Divider Rods.................................................................................................................. 87
Removing Crop Divider Rods .......................................................................................... 88
Rice Dividers.................................................................................................................. 88
3.8 Auto Header Height Control (AHHC)............................................................................................... 89
3.8.1 Auto Header Height Control Sensor Output Voltage Range – Combine Requirements ................ 91
Manually Checking Voltage Range................................................................................... 91
Adjusting Voltage Limits .................................................................................................. 93
3.8.2 Challenger 6 and 7 Series Combines....................................................................................... 94
Checking Voltage Range from the Combine Cab (Challenger 6 and 7 Series)..................... 94
Engaging the Auto Header Height Control (Challenger 6 Series)........................................ 96
Calibrating the Auto Header Height Control (Challenger 6 Series)...................................... 97
Adjusting the Header Height (Challenger 6 Series)............................................................ 99
Adjusting the Header Raise/Lower Rate (Challenger 6 Series)........................................... 99
Setting the Sensitivity of the Auto Header Height Control (Challenger 6 Series) .................100
3.8.3 Case IH 2300/2500 and 5088/6088/7088 Combines................................................................ 101
Engaging the Auto Header Height Control (Case IH 2300)................................................ 101
Calibrating the Auto Header Height Control (Case IH 2300/2500 and
5088/6088/7088)........................................................................................................ 103
Setting the Sensitivity of the Auto Header Height (Case IH 2300/2500 and
5088/6088/7088)........................................................................................................ 104
3.8.4 Case IH 5130/6130/7130, 7010/8010, 7120/8120/9120, and 7230/8230/9230 Combines ........... 105
Checking Voltage Range from the Combine Cab (Case 8010) ..........................................105
Checking Voltage Range from the Combine Cab (Case IH 5130/6130/7130, 7010/8010;
7120/8120/9120; 7230/8230/9230)..............................................................................108
Calibrating the Auto Header Height Control (Case IH 5130/6130/7130, 7010/8010;
7120/8120/9120; 7230/8230/9230)..............................................................................110
Calibrating the Auto Header Height Control System (Case Combines with Version
28.00 Software)..........................................................................................................112
147695
v
iii
Revision A