TABLE OF CONTENT
S
3.8.5 Gleaner R62/R72 Combines ..................................................................................................114
Determining System Requirements (Gleaner R62/R72)....................................................114
Calibrating the Auto Header Height Control (Gleaner R62/R72)........................................114
Setting the Sensitivity of the Auto Header Height Control (Gleaner R62/R72 Series) ...........114
3.8.6 Gleaner R65/R75 Combines ..................................................................................................117
Checking Voltage Range from the Combine Cab (Gleaner R65/R75) ................................117
Engaging the Auto Header Height Control (Gleaner R65/R75)..........................................118
Calibrating the Auto Header Height Control (Gleaner R65/R75) ........................................120
Turning the Accumulator Off (Gleaner R65/R75).............................................................. 121
Adjusting the Header Raise/Lower Rate (Gleaner R65/R75)............................................. 122
Adjusting Ground Pressure (Gleaner R65/R75)................................................................ 122
Adjusting the Sensitivity of the Auto Header Height Control (Gleaner R65/R75) ................. 123
Troubleshooting Alarms and Diagnostic Faults (Gleaner R65/R75) ................................... 124
3.8.7 John Deere 50 Series Combines............................................................................................ 127
Checking Voltage Range from the Combine Cab (John Deere 50 Series).......................... 127
Calibrating the Auto Header Height Control (John Deere 50 Series)..................................129
3.8.8 John Deere 60 Series Combines............................................................................................ 131
Checking Voltage Range from the Combine Cab (John Deere 60 Series).......................... 131
Calibrating the Auto Header Height Control (John Deere 60 Series)..................................132
Turning the Accumulator Off (John Deere 60 Series)........................................................134
Setting the Sensing Grain Header Height to 50 (John Deere 60 Series).............................134
Setting the Sensitivity of the Auto Header Height Control (John Deere 60 Series) .............. 135
Adjusting the Threshold for the Drop Rate Valve (John Deere 60 Series) ...........................136
3.8.9 John Deere 70 Series Combines............................................................................................ 137
Checking Voltage Range from the Combine Cab (John Deere 70 Series).......................... 137
Calibrating Feeder House Speed (John Deere 70 Series) ................................................. 141
Calibrating the Auto Header Height Control (John Deere 70 Series)..................................141
Setting the Sensitivity of the Auto Header Height Control (John Deere 70 Series) .............. 142
Adjusting the Manual Header Raise/Lower Rate (John Deere 70 Series)........................... 142
3.8.10 John Deere S Series Combines ............................................................................................. 143
Checking Voltage Range from the Combine Cab (John Deere S Series)............................143
Calibrating the Auto Header Height Control (John Deere S Series) ...................................146
Setting the Sensitivity of the Auto Header Height Control (John Deere S Series) ................ 148
Adjusting the Manual Header Raise/Lower Rate (John Deere S Series) ............................ 149
3.8.11 Lexion 500 Series Combines ................................................................................................. 150
Calibrating the Auto Header Height Control (Lexion 500 Series) ....................................... 150
Setting Cutting Height (Lexion 500 Series) ...................................................................... 152
3.8.12 Lexion 700 Series Combines ................................................................................................. 157
Calibrating the Auto Header Height Control (Lexion 700 Series) ....................................... 157
Setting Cutting Height (Lexion 700 Series) ...................................................................... 160
Setting the Sensitivity of the Auto Header Height Control (Lexion 700 Series) .................... 160
Adjusting Auto Reel Speed (Lexion 700 Series)...............................................................162
3.8.13 New Holland Combines .........................................................................................................163
Checking Voltage Range from the Combine Cab (New Holland) .......................................163
Engaging the Auto Header Height Control (New Holland CR/CX Series) ........................... 166
Calibrating the Auto Header Height Control (New Holland CR/CX Series)..........................167
Adjusting Header Raise Rate (New Holland CR/CX Series).............................................. 169
Setting the Header Lower Rate to 50 (New Holland CR/CX Series)................................... 170
Setting the Sensitivity of the Auto Header Height Control to 200 (New Holland CR/CX
Series).......................................................................................................................170
3.8.14 Sensor Operation..................................................................................................................171
3.9 Le ve llin g the Heade r ..................................................................................................................... 173
3.10 Unplugging Cutterbar.................................................................................................................... 175
3.11 Unplugging Adapter...................................................................................................................... 176
147695
i
x
Revision A
To Next Page
Loading...
