Rohde & Schwarz SMBV100B - LF Generator Settings

Remote Control Commands
R&S
®
SMBV100B
839User Manual 1178.4460.02 ─ 03
// SOURce1:LFOutput2:SHAPe TRAP
// SOURce1:LFOutput2:SHAPe:PULSe:PERiod 0.2
// SOURce1:LFOutput2:SHAPe:TRAPeze:RISE 0.0001
// SOURce1:LFOutput2:SHAPe:TRAPeze:FALL 0.001
// SOURce1:LFOutput2:SHAPe:TRAPeze:FALL 0.0001
// SOURce1:LFOutput2:SHAPe:TRAPeze:HIGH 0.0005
// SOURce1:LFOutput2:SHAPe TRI
// SOURce1:LFOutput2:SHAPe:PULSe:PERiod 0.1
// SOURce1:LFOutput2:SHAPe:TRIangle:RISE 0.0001
// activate the LF output and select the LF1 as signal source
// configure the LF output signal
SOURce1:LFOutput1:FREQuency:MODE CW
SOURce1:LFOutput1:STATe 1
SOURce1:LFOutput1:SOURce LF1
SOURce1:LFOutput1:INTernal:VOLTage 1
SOURce1:LFOutput1:OFFSet 0.001
● LF Generator Settings...........................................................................................839
● LF Sweep Settings................................................................................................847
12.16.10.1 LF Generator Settings
With the commands described in this section, you can configure the LF signal source.
[:SOURce]:LFOutput<ch>:BANDwidth?............................................................................840
[:SOURce]:LFOutput<ch>:FREQuency.............................................................................840
[:SOURce<hw>]:LFOutput<ch>:PERiod?..........................................................................840
[:SOURce<hw>]:LFOutput:FREQuency:MANual............................................................... 841
[:SOURce<hw>]:LFOutput:FREQuency:MODE................................................................. 841
[:SOURce<hw>]:LFOutput:FREQuency:STOP.................................................................. 841
[:SOURce<hw>]:LFOutput:FREQuency:STARt..................................................................841
[:SOURce]:LFOutput<ch>[:STATe]................................................................................... 842
[:SOURce]:LFOutput<ch>:INTernal:VOLTage....................................................................842
[:SOURce]:LFOutput:OFFSet.......................................................................................... 842
[:SOURce]:LFOutput<ch>:SOURce................................................................................. 843
[:SOURce]:LFOutput:SIMPedance...................................................................................843
[:SOURce]:LFOutput<ch>:SOURce:PATH........................................................................ 843
[:SOURce]:LFOutput:VOLTage........................................................................................ 844
[:SOURce<hw>]:LFOutput<ch>:SHAPe............................................................................844
[:SOURce<hw>]:LFOutput<ch>:SHAPe:PULSe:DCYCle....................................................844
[:SOURce<hw>]:LFOutput<ch>:SHAPe:PULSe:PERiod.....................................................844
[:SOURce<hw>]:LFOutput<ch>:SHAPe:PULSe:WIDTh......................................................845
[:SOURce<hw>]:LFOutput<ch>:SHAPe:TRAPeze:FALL.................................................... 845
[:SOURce<hw>]:LFOutput<ch>:SHAPe:TRAPeze:HIGH....................................................845
[:SOURce<hw>]:LFOutput<ch>:SHAPe:TRAPeze:PERiod................................................. 846
[:SOURce<hw>]:LFOutput<ch>:SHAPe:TRAPeze:RISE.................................................... 846
[:SOURce<hw>]:LFOutput<ch>:SHAPe:TRIangle:PERiod..................................................846
[:SOURce<hw>]:LFOutput<ch>:SHAPe:TRIangle:RISE..................................................... 846
SOURce Subsystem