Siemens SINAMICS G120XA - Page 897

CO/BO: Free tec_ctrl 2 status word
r11249.0...11, 700
CO/BO: Gating unit status word 1
r1838.0...15, 539
CO/BO: Hibernation mode status words
r2399.0...8, 635
CO/BO: Limit switch status word
r3344.0...5, 649
CO/BO: Missing enable signal
r0046.0...31, 361
CO/BO: Mot_temp status word faults/alarms
r5389.0...8, 662
CO/BO: Multi-pump control bypass command
r29545, 711
CO/BO: Multi-pump control feedback signal for
contactor
r29549, 712
CO/BO: Multi-pump control service mode interlock
manually
p29542.0...3, 710
CO/BO: Multi-pump control status word
r29529.0...7, 708
CO/BO: NAMUR message bit bar
r3113.0...15, 638
CO/BO: PM330 digital inputs status
r4022.0...3, 660
CO/BO: PM330 digital inputs status inverted
r4023.0...3, 660
CO/BO: PolID diagnostics
r1992.0...15, 551
CO/BO: Safely remove memory card status
r9401.0...3, 682
CO/BO: Skip band status word
r1099.0, 479
CO/BO: Status word 1
r0052.0...15, 364
CO/BO: Status word 2
r0053.0...11, 366
r0053.1...11, 365
CO/BO: Status word faults/alarms 1
r2139.0...15, 587
CO/BO: Status word faults/alarms 2
r2135.12...15, 586
CO/BO: Status word monitoring 1
r2197.0...13, 600
CO/BO: Status word monitoring 2
r2198.4...12, 601
CO/BO: Status word monitoring 3
r2199.0...5, 602
CO/BO: Status word sequence control
r0899.0...11, 455
CO/BO: Status word speed controller
r1407.0...23, 519
CO/BO: Status word, closed-loop control
r0056.0...15, 369
CO/BO: Status word: application
r29629, 719
CO/BO: Status word:command
r29659, 722
CO/BO: Supplementary control word
r0055.0...15, 367, 368
CO/BO: Technology controller fixed value selection
status word
r2225.0, 607
CO/BO: Technology controller status word
r2349.0...13, 625
CO/BO: Write protection/know-how protection status
r7760.0...12, 665
CO: Absolute actual current smoothed
r0027, 356
CO: Absolute current actual value
r0068[0...1], 371
CO: Accelerating torque
r1518[0...1], 523
CO: Active power actual value
r0082[0...2], 374
CO: Active power actual value smoothed
r0032, 356
CO: Actual alarm code
r2132, 585
CO: Actual component number
r3132, 642
CO: Actual DC link voltage
r0070, 372
CO: Actual fault code
r2131, 585
CO: Actual fault value
r3131, 642
CO: Actual power factor
r0087, 374
CO: Actual slip compensation
r1337, 515
CO: Actual speed
r0063[0...2], 370
CO: Actual speed smoothed
r0021, 354
CO: Actual speed smoothed signals
r2169, 594
CO: Counter alarm buffer changes
r2121, 582
CO: Counter for fault buffer changes
r0944, 455
Index
SINAMICS G120XA converter
Operating Instructions, 03/2019, FW V1.0, A5E44751205B AB 895