Enterasys D2 D2G124-12P User Manual

set port lacp
4-44 Port Configuration
set port lacp
Usethiscommandtosetlinkaggregationparametersforoneormoreports.Thesesettingswill
determinethespecifiedunderlyingphysicalports’abilitytojoinaLAG, andtheiradministrative
stateonceaggregated.
Syntax
set port lacp port port-string {[aadminkey aadminkey] [aadminstate {lacpactive |
lacptimeout | lacpagg | lacpsync | lacpcollect | lacpdist | lacpdef | lacpexpire}]
[aportpri aportpri] [asyspri asyspri] [enable | [disable] [padminkey padminkey]
[padminport padminport] [padminportpri padminportpri] [padminstate {lacpactive |
lacptimeout | lacpagg | lacpsync | lacpcollect | lacpdist | lacpdef | lacpexpire}]
[padminsysid padminsysid] [padminsyspri padminsyspri]
Parameters
portport‐string Specifiesthephysicalport(s)onwhichtoconfigureLACP.Foradetailed
descriptionofpossibleport‐stringvalues,referto“PortStringSyntaxUsed
intheCLI”onpage4‐1.
aadminkey
aadminkey
Setstheport’sactoradminkey.LACPwillusethisvaluetoformanoper
keyandwilldeterminewhichunderlyingphysicalportsarecapableof
aggregatingbycomparingoperkeys.Aggregatorportsallowonly
underlyingportswithoperkeysmatchingtheirstojointheirLAG.Valid
valuesare1‐65535.Thedefaultkeyvalueis32768.
aadminstate
lacpactive|
lacptimeout|
lacpagg|lacpsync
|lacpcollect|
lacpdist|lacpdef|
lacpexpire
Setstheport’sactorLACPadministrativestatetoallowfor:
lacpactive‐TransmittingLACPPDUs.
lacptimeout‐TransmittingLACPPDUsevery1sec.vs30sec.(default).
lacpagg‐Aggregationonthisport.
lacpsync‐Transitiontosynchronizationstate.
lacpcollect‐Transitiontocollectionstate.
lacpdist‐Transition
todistributionstate.
lacpdef‐Transitiontodefaultedstate.
lacpexpire‐Transitiontoexpiredstate.
aportpriaportpri Setstheport’sactorportpriority.Validvaluesare0‐65535,withlower
valuesdesignatinghigherpriority.
asyspriasyspri Setstheport’sactorsystempriority.TheLACP implementationontheD‐
Seriesdeviceusesthisvalueto
determineaggregationprecedencewhen
therearetwodevicescompetingforthesameaggregator.Validvaluesare
0‐65535,withhigherprecedencegiventolowervalues.
Note: Only one LACP system priority can be set on a D-Series
device, using either this command, or the set lacp asyspri command
(“set lacp asyspri” on page 4-38).
enable (Optional)EnablesLACPDUprocessingonthisport.
disable (Optional)DisablesLACPDUprocessingonthisport.
padminkey
padminkey
Setsadefaultvaluetouseastheport’spartneradminkey.Onlyports
withmatchingadminkeysareallowedtoaggregate.Validvaluesare1‐
65535.

Enterasys D2 D2G124-12P Specifications

General

Brand	Enterasys
Model	D2 D2G124-12P
Category	Network Router
Language	English