Lenze i550

17.4.2 Network diagnoscs
The following parameters show some general informaon with regard to the network opon
available and the network.
Parameter
Address Name / seng range / [default seng] Info
0x282B:005
(P125.05)
Inverter diagnoscs: Most recently used control regis-
ter
(Inverter diag.: Netw. contr.reg.)
•
Read only
Display of the network register for the control that was accessed last
(e. g. 0x6040 or 0x400B:1).
•
Format: 0xiiiiss00 (iiii = hexadecimal index, ss = hexadecimal subindex)
•
The lowest byte is always 0x00.
0x282B:006
(P125.06)
Inverter diagnoscs: Most recently used setpoint reg-
ister
(Inverter diag.: Netw. setp.reg.)
•
Read only
Display of the network register for setpoint selecon that was accessed
last (e. g. 0x6042 or 0x400B:3).
•
Format: 0xiiiiss00 (iiii = hexadecimal index, ss = hexadecimal subindex)
•
The lowest byte is always 0x00.
0x231F:001
(P500.01)
Module ID: Acve module ID
(Module ID: Acve module ID)
•
Read only
Display of the network opons currently congured in the inverter.
•
With the help of this module ID, the keypad only shows the communi-
caon parameters relevant to the respecve network.
Note!
When switched on, the inverter checks whether the parameter sengs
saved in the memory module match the inverter hardware and rm-
ware. In case of an incompability, a corresponding error message is
output. For details see chapter "Behaviour of the inverter in case of
incompable data in the memory module" (secon "Hardware and rm-
ware updates/downgrades"). ^ 516
48 No network
67 CANopen
71 EtherNet/IP (from version 02.00)
72 BACnet
78 POWERLINK (from version 05.00)
80 PROFIBUS
82 PROFINET (from version 02.00)
84 EtherCAT (from version 02.00)
86 Modbus TCP/IP
87 Modbus
0x231F:002
(P500.02)
Module ID: Module ID connected
(Module ID: Module ID conn.)
•
Read only
Display of the network opon currently available in the inverter.
Note!
When switched on, the inverter checks whether the parameter sengs
saved in the memory module match the inverter hardware and rm-
ware. In case of an incompability, a corresponding error message is
output. For details see chapter "Behaviour of the inverter in case of
incompable data in the memory module" (secon "Hardware and rm-
ware updates/downgrades"). ^ 516
48 No network Display of the network opons currently congured in the inverter.
•
With the help of this module ID, the keypad only shows the communi-
caon parameters relevant to the respecve network.
Note!
When switched on, the inverter checks whether the parameter sengs
saved in the memory module match the inverter hardware and rm-
ware. In case of an incompability, a corresponding error message is
output. For details see chapter "Behaviour of the inverter in case of
incompable data in the memory module" (secon "Hardware and rm-
ware updates/downgrades"). ^ 516
67 CANopen
71 EtherNet/IP (from version 02.00)
72 BACnet
78 POWERLINK (from version 05.00)
80 PROFIBUS
82 PROFINET (from version 02.00)
84 EtherCAT (from version 02.00)
86 Modbus TCP/IP
87 Modbus
Related topics
4Conguring the network ^ 280
Diagnoscs and fault eliminaon
Diagnosc parameters
Network diagnoscs
604