Lenze i550 - Basic Setting and Options

Restart of the communicaon
The communicaon needs to be restarted aer the EtherNet/IP conguraon is changed, so
that the changed sengs can take eect.
For restarng communicaon, there are two opons:
a)
Switch inverter o and on again.
b)
0x23A0 (P508.00) Set = "Restart with current values [1]".
Parameter
Address Name / seng range / [default seng] Info
0x23A0
(P508.00)
EtherNet/IP communicaon
(EtherN/IP comm.)
•
From version 02.00
Restart / stop communicaon.
•
When the device command has been executed successfully, the value
0 is shown.
•
A communicaon restart has nothing to do with the acceptance of the
described operang modes. For this purpose, a restart of the device is
required!
0 No acon/no error Only status feedback
1 Restart with current values Restart communicaon with the current values.
2 Restart with default values Restart communicaon with the standard values.
5 Stop network communicaon Stop communicaon.
10 In process Only status feedback
11 Acon cancelled
12 Fault
12.11.2 Basic seng and opons
Parameter
Address Name / seng range / [default seng] Info
0x23A3
(P509.00)
EtherNet/IP switch posion
(EtherN. switch)
•
Read only
•
From version 02.00
Display of the rotary encoder switch sengs at the last mains power-on.
0x23A1:001
(P510.01)
EtherNet/IP sengs: IP address
(EtherN/IP se.: IP address)
0.0.0.0 ... [192.168.124.16] ... 255.255.255.255
•
From version 02.00
Set IP address.
The default seng 276605120 corresponds to the IP address
192.168.124.16.
•
276605120 = 0x107CA8C0 à 0xC0.0xA8.0x7C.0x10 = 192.168.124.16
0x23A1:005
(P510.05)
EtherNet/IP sengs: IP conguraon
(EtherN/IP se.: IP conguraon)
•
From version 02.00
Set IP conguraon.
0 Stored IP The currently saved IP conguraon is used.
1 BOOTP The IP conguraon is assigned by the Scanner via BOOTP.
2 DHCP The IP conguraon is assigned by the Scanner via DHCP.
The assignment of a gateway address that is not in the same subnetwork
as the IP address, is denied.
0x23A1:002
(P510.02)
EtherNet/IP sengs: Subnet
(EtherN/IP se.: Subnet)
0.0.0.0 ... [255.255.255.0] ... 255.255.255.255
•
From version 02.00
Set subnet mask.
The default seng 16777215 corresponds to the subnet mask
255.255.255.0.
•
16777215 = 0xFFFFFF à 0xFF.0xFF.0xFF.0x00 = 255.255.255.0
0x23A1:003
(P510.03)
EtherNet/IP sengs: Gateway
(EtherN/IP se.: Gateway)
0.0.0.0 ... [0.0.0.0] ... 255.255.255.255
•
From version 02.00
Set gateway address.
Example:
The seng 276344004 corresponds to the gateway address
196.172.120.16.
•
276344004 = 0x1078ACC4 à 0xC4.0xAC.0x78.0x10 = 196.172.120.16
0x23A1:004
(P510.04)
EtherNet/IP sengs: Host name
(EtherN/IP se.: Host name)
•
From version 02.00
Set host name.
•
String with up to 64 characters.
0x23A1:006
(P510.06)
EtherNet/IP sengs: Mulcast TTL
(EtherN/IP se.: Mulcast TTL)
1 ... [1] ... 255
•
From version 02.00
Seng of the mulcast TTL value for the validity period of data packets
in the network. The TTL value denes the number of hops that the mul-
cast message can distribute via routers.
Conguring the network
EtherNet/IP
Commissioning
398