Lenze i550

t
t
0 Hz
30 Hz
10 Hz
20 Hz
40 Hz
50 Hz
60 Hz
0 Hz
30 Hz
10 Hz
20 Hz
40 Hz
50 Hz
60 Hz
t
t
t
t
t
t
t
t
t
t
0x2DDD
Seq. controlled [100] Digital output 1
Seq. controlled [100] Relay
Seg2
t
Seg1
t
End seg
t
Seg2
t
Seg1
t
Bit 0 = 1 and bit 1 ... 3 = 0: sequence 1 is selected.
Sequence active [101]
Segment 2
(30 Hz)
Segment 1
(40 Hz)
End segment
(10 Hz)
Segment 2
(30 Hz)
Segment 1
(40 Hz)
Start sequenceDigital input 2 [12]
RunDigital input 1 [11]
Running [50]
Stop active [53]
Select sequence (bit 0)
Digital input 3 [13]
Constant TRUE [1]
Constant TRUE [1]
Output signals
Status signals
Output frequency
Abort sequence
Enable inverter
Input signals
Frequency setpoint selection
FunctionTrigger
The status signals can be assigned to digital outputs. 4Congure digital outputs^ 263
①
If the inverter is enabled and no error is acve, the motor can be started with the "Run" funcon.
As the sequence has not been started yet, rst the normal setpoint control is acve.
②
The "Start sequence" funcon is used to start the selected sequence in an edge-controlled way.
③
Sequencer mode0x4025 (P800.00) = "Time operaon [1]":
The switch-over to the next step of the sequence is made aer the me set for the current segment has elapsed.
④
The segment 2 is congured here in such a way that the relay will be triggered during the me of processing.
⑤
End of sequence mode0x402F (P824.00) = "Keep running [0]":
Aer the sequence has been processed, the setpoint set for the end segment is connuously transmied to the motor control unl the
sequence is aborted.
⑥
In case of the end segment, the me seng determines the delay aer which the congured output states are to become acve. Here, the
end segment is congured in such a way that the digital output 1 is set aer 10 s have expired.
⑦
If the "Run" funcon is set to FALSE, the motor is stopped with the stop method set in 0x2838:003 (P203.03). The started sequence, how-
ever, remains acve and the sequencer-controlled outputs keep their state.
⑧
Start of sequence mode0x4040 (P820.00) = "Restart sequencer [0]":
If the "Run" funcon is set to TRUE again, the (sll acve) sequence is restarted.
⑨
The "Abort sequence" funcon is used to abort the sequence in an edge-controlled way.
In this case, the standard setpoint or the setpoint source selected via setpoint change-over is acve again.
7.2.4.5 Sequencer diagnoscs
The following parameters serve to diagnose the "sequencer" funcon.
Parameter
Address Name / seng range / [default seng] Info
0x2DAE:001
(P140.01)
Sequencer diagnoscs: Acve step
(Sequencer diag: Acve Step)
•
Read only
•
From version 03.00
Display of the acve step.
•
0 ≡ no sequence acve.
0x2DAE:002
(P140.02)
Sequencer diagnoscs: Step me elapsed
(Sequencer diag: StepTime elapsed)
•
Read only: x.x s
•
From version 03.00
Display of the me that has passed since the start of the current step.
Conguring the frequency control
Congure setpoint sources
Sequencer
114