Lenze i550

Address Name / seng range / [default seng] Info
0x2631:018
(P400.18)
Funcon list: Acvate preset (bit 0)
(Funcon list: Setp: Preset b0)
•
Further seng opons: 4Trigger list ^ 64
Assignment of a trigger for the "Acvate preset (bit 0)" funcon.
The bit with the valency 2
0
for bit-coded selecon and the acvaon of a
parameterised setpoint (preset).
Trigger = FALSE: bit = "0".
Trigger = TRUE: bit = "1".
14 Digital input 4 State of X3/DI4, taking an inversion set in 0x2632:004 (P411.04) into
consideraon.
0x2631:019
(P400.19)
Funcon list: Acvate preset (bit 1)
(Funcon list: Setp: Preset b1)
•
Further seng opons: 4Trigger list ^ 64
Assignment of a trigger for the "Acvate preset (bit 1)" funcon.
The bit with the valency 2
1
for bit-coded selecon and the acvaon of a
parameterised setpoint (preset).
Trigger = FALSE: bit = "0".
Trigger = TRUE: bit = "1".
15 Digital input 5 State of X3/DI5, taking an inversion set in 0x2632:005 (P411.05) into
consideraon.
0x2631:020
(P400.20)
Funcon list: Acvate preset (bit 2)
(Funcon list: Setp: Preset b2)
•
Further seng opons: 4Trigger list ^ 64
Assignment of a trigger for the "Acvate preset (bit 2)" funcon.
The bit with the valency 2
2
for bit-coded selecon and the acvaon of a
parameterised setpoint (preset).
Trigger = FALSE: bit = "0".
Trigger = TRUE: bit = "1".
0 Not connected No trigger assigned (trigger is constantly FALSE).
0x2631:021
(P400.21)
Funcon list: Acvate preset (bit 3)
(Funcon list: Setp: Preset b3)
•
Further seng opons: 4Trigger list ^ 64
Assignment of a trigger for the "Acvate preset (bit 3)" funcon.
Selecon bit with the valency 2
3
for the bit-coded selecon and acva-
on of a parameterised setpoint (preset value).
Trigger = FALSE: selecon bit = "0".
Trigger = TRUE: selecon bit = "1".
0 Not connected No trigger assigned (trigger is constantly FALSE).
0x2631:022
(P400.22)
Funcon list: Acvate setpoint via HTL input
(Funcon list: Setp: HTL input)
•
Further seng opons: 4Trigger list ^ 64
Assignment of a trigger for the "Acvate setpoint via HTL input" func-
on.
Trigger = TRUE: HTL input is used as setpoint source (if the trigger
assigned has the highest setpoint priority).
Trigger = FALSE: no acon / deacvate funcon again.
0 Not connected No trigger assigned (trigger is constantly FALSE).
0x2631:025
(P400.25)
Funcon list: Acvate MOP setpoint
(Funcon list: Setp: MOP)
•
Further seng opons: 4Trigger list ^ 64
Assignment of a trigger for the "Acvate MOP setpoint" funcon.
Trigger = TRUE: the "Motor potenometer" funcon is used as setpoint
source (if the trigger assigned has the highest setpoint priority).
Trigger = FALSE: no acon / deacvate funcon again.
0 Not connected No trigger assigned (trigger is constantly FALSE).
0x2631:026
(P400.26)
Acvate segment setpoint (bit 0)
(Setp: Segment b0)
•
From version 03.00
•
Further seng opons: 4Trigger list ^ 64
Assignment of a trigger for the "Acvate segment setpoint (bit 0)" func-
on.
Selecon bit with the valency 20 for the bit-coded selecon and acva-
on of a parameterised segment setpoint.
Trigger = FALSE: selecon bit = "0".
Trigger = TRUE: selecon bit = "1".
Notes:
•
During normal operaon (no acve sequence), this funcon serves to
acvate the setpoint of a segment (instead of an enre sequence in
the sequencer operaon).
•
This funcon is not intended for the use in the sequencer operaon.
0 Not connected No trigger assigned (trigger is constantly FALSE).
0x2631:027
(P400.27)
Acvate segment setpoint (bit 1)
(Setp: Segment b1)
•
From version 03.00
•
Further seng opons: 4Trigger list ^ 64
Assignment of a trigger for the "Acvate segment setpoint (bit 1)" func-
on.
Selecon bit with the valency 2
1
for the bit-coded selecon and acva-
on of a parameterised segment setpoint.
Trigger = FALSE: selecon bit = "0".
Trigger = TRUE: selecon bit = "1".
Notes:
•
During normal operaon (no acve sequence), this funcon serves to
acvate the setpoint of a segment (instead of an enre sequence in
the sequencer operaon).
•
This funcon is not intended for the use in the sequencer operaon.
0 Not connected No trigger assigned (trigger is constantly FALSE).
Conguring the frequency control
Changing the setpoint source during operaon
132