Lenze i550 - Page 700

Address Designaon Default seng Category Data type Factor A M
0x402E:002
(P822.02)
End segment: Acceleraon/deceleraon 5.0 s Sequencer U16 10 P -
0x402E:003
(P822.03)
End segment: Time 0.0 s Sequencer U32 10 P -
0x402E:004
(P822.04)
End segment: Digital outputs 0 Sequencer U8 1 P -
0x402E:005
(P822.05)
End segment: Analog outputs 0.00 VDC Sequencer U16 100 P -
0x402E:006
(P822.06)
End segment: PID setpoint 0.00 PID unit Sequencer I16 100 P -
0x402E:007
(P822.07)
End segment: Torque setpoint 100.0 % Sequencer I16 10 P -
0x402E:008 End segment: NetWordOUT2 0 Sequencer U16 1 P -
0x402E:009 End segment: Reserved 0 Sequencer U32 1 P -
0x402F
(P824.00)
End of sequence mode Keep running [0] Sequencer U8 1 P -
0x4030:001 ...
0x4030:016
(P830.01 ... 16)
Sequence 1: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x4031
(P831.00)
Number of cycles sequence 1 1 Sequencer U16 1 P -
0x4032:001 ...
0x4032:016
(P835.01 ... 16)
Sequence 2: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x4033
(P836.00)
Number of cycles sequence 2 1 Sequencer U16 1 P -
0x4034:001 ...
0x4034:016
(P840.01 ... 16)
Sequence 3: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x4035
(P841.00)
Number of cycles sequence 3 1 Sequencer U16 1 P -
0x4036:001 ...
0x4036:016
(P845.01 ... 16)
Sequence 4: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x4037
(P846.00)
Number of cycles sequence 4 1 Sequencer U16 1 P -
0x4038:001 ...
0x4038:016
(P850.01 ... 16)
Sequence 5: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x4039
(P851.00)
Number of cycles sequence 5 1 Sequencer U16 1 P -
0x403A:001 ...
0x403A:016
(P855.01 ... 16)
Sequence 6: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x403B
(P856.00)
Number of cycles sequence 6 1 Sequencer U16 1 P -
0x403C:001 ...
0x403C:016
(P860.01 ... 16)
Sequence 7: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x403D
(P861.00)
Number of cycles sequence 7 1 Sequencer U16 1 P -
0x403E:001 ...
0x403E:016
(P865.01 ... 16)
Sequence 8: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x403F
(P866.00)
Number of cycles sequence 8 1 Sequencer U16 1 P -
0x4040
(P820.00)
Start of sequence mode Restart sequencer [0] Sequencer U8 1 P -
* Default seng depending on the size.
Appendix
Parameter aribute list
700