Freescale Semiconductor MPC5553 - Page 106

MPC5553/MPC5554 Microcontroller Reference Manual, Rev. 5
Freescale Semiconductor 2-59
V
DDE3
2
1.8–3.3 V DATA[0:15]_GPIO[28:43], DATA[16]_FEC_TX_CLK_CAL_DATA[0]_GPIO[44],
DATA[17]_FEC_CRS_CAL_DATA[1]_GPIO[45],
DATA[18]_FEC_TX_ER_CAL_DATA[2]_GPIO[46],
DATA[19]_FEC_RX_CLK_CAL_DATA[3]_GPIO[47],
DATA[20]_FEC_TXD[0]_CAL_DATA[4]_GPIO[48],
DATA[21]_FEC_RX_ER_CAL_DATA[5]_GPIO[49],
DATA[22]_FEC_RXD[0]_CAL_DATA[6]_GPIO[50],
DATA[23]_FEC_TXD[3]_CAL_DATA[7]_GPIO[51],
DATA[24]_FEC_COL_CAL_DATA[8]_GPIO[52],
DATA[25]_FEC_RX_DV_CAL_DATA[9]_GPIO[53],
DATA[26]_FEC_TX_EN_CAL_DATA[10]_GPIO[54],
DATA[27]_FEC_TXD[2]_CAL_DATA[11]_GPIO[55],
DATA[28]_FEC_TXD[1]_CAL_DATA[12]_GPIO[56],
DATA[29]_FEC_RXD[1]_CAL_DATA[13]_GPIO[57],
DATA[30]_FEC_RXD[2]_CAL_DATA[14]_GPIO[58],
DATA[31]_FEC_RXD[3]_CAL_DATA[15]_GPIO[59], OE
_GPIO[68],
BR
3
_CAL_ADDR[10]_FEC_MDC_CAL_CS[2]_ GPIO[72],
BG
3
_CAL_ADDR[11]_FEC_MDIO_CAL_CS[3]_GPIO[73], GPIO[206:207]
V
DDE5
1.8–3.3 V CLKOUT, ENGCLK
V
DDE7
1.8–3.3 V EVTI, EVTO, MCKO, MDO[3:0], MDO[11:4]_GPIO[82:75], MSEO[1:0], RDY, TCK,
TDI, TDO, TMS, JCOMP, TEST
V
DDSYN
3.3 V XTAL, EXTAL_EXTCLK
V
RC33
3.3 V V
RCCTL
V
DDA0
5.0 V
AN[22:35], V
RH,
V
RL,
REFBYPC
V
DDA1
5.0 V
AN[0]_DAN0+, AN[1]_DAN0-, AN[2]_DAN1+, AN[3]_DAN1-, AN[4]_DAN2+,
AN[5]_DAN2-, AN[6]_DAN3+, AN[7]_DAN3-, AN[8]_ANW, AN[9]_ANX, AN[10]_ANY,
AN[11]_ANZ, AN[16:21], AN[36:39]
V
SSA0
GND Analog Ground Input ADC0
V
SSA1
GND Analog Ground Input
Other Power Segments
V
PP
4.5–5.25 V
4
—
V
FLASH
3.0–3.6 V —
V
DD33
3.0–3.6 V —
V
STBY
0.9–1.1 V —
1
These are nominal voltages. V
DDE
is 1.62–3.6 V; V
DDEH
is 3.0–5.5 V. All V
DDE
voltages are  10%; V
DDEH
voltages are
+5%/–10%.V
RC33
is  10%; V
DDSYN
is  10%; V
DDA1
is + 5%, –10%.
2
V
DDE2
and V
DDE3
are separate segments in the MPC5553 pad ring. These segments are shorted together in the package
substrate.
3
The BR and BG functions are not implemented on the MPC5553 and are replaced by FEC and calibration functions. The pin
name on the ball map, however, does remain BR
and BG. The primary functions for these pins are CAL_ADDR[10] and
CAL_ADDR[11], respectively.
4
During read operations, V
PP
can be as high as 5.3 V or as low as 3.0 V.
Table 2-3. MPC5553 Power/Ground Segmentation
Power
Segment
Voltage
1
I/O Pins Powered by Segment