Toshiba e-STUDIO 6550Ce-STUDIO 5560C - Adjustment for Medium-Sized Paper

e-STUDIO5540C/6540C/6550C/5560C/6560C/6570C © 2011 - 2015 TOSHIBA TEC CORPORATION All rights reserved
SETTING ADJUSTMENT
6 - 22
[E-3] Adjustment for medium-sized paper (Length: 220 to 329 mm)
1. While pressing [0] and [5] simultaneously, turn the power ON.  (Adjustment Mode)
2. Press [3]  [FAX]. (A grid pattern with 10 mm squares is printed out. Use A4-R/LT-R from the
1st drawer.)
3. Check the grid pattern on the test print and measure the distance E from the left edge of the
paper to the 6th line of the grid pattern.
4. Check if the distance E is within 52±0.5 mm.
5. If not, use the following procedure to change values and measure the distance E again.
<Procedure>
(Adjustment Mode)  (Key in the code [4019])  [START]  [2]  [START]
 (Key in a value (acceptable values: 0 to 255))
 [OK] or [INTERRUPT] (Stored in memory)
 “100% A” is displayed
 Press [3]  [FAX]  (A grid pattern is printed out.)
* The larger the adjustment value is, the longer the distance E becomes (approx. 0.04 mm/
step).
Notes:
When the laser writing start position (05-4019-0) for long-sized paper is changed, the one for
medium-sized paper is also altered. (However, the value of 05-4019-2 is not changed.)
If 05-4019-0 is changed, check it with A4-R/LT-R paper and adjust the value of 05-4019-2 again
as required.
<Adjustment procedure summarization for A to E>
[0] [5] [Power ON]  [98] ([3] (05-4062, 4019) for duplexing)  [FAX]
A: 05-4772 (2nd drawer, A3/LD)  200±0.5 mm (0.1 mm/step)
B: 05-4006 (2nd drawer, A3/LD)  52±0.5 mm (0.04 mm/step)
05-
4018-0 (1st drawer, A4/LT)
05-
4018-1 (2nd drawer, A3/LD)
05-
4018-2 (3rd drawer, A4/LT)
05-
4018-3 (4th drawer, A4/LT)
05-
4018-4 (Tandem LCF, A4/LT)
05-
4018-5 (Bypass feed, A4/LT)
05-
4018-6 (Option LCF, A4/LT)
C: 05-4526-0 to 3 (2nd drawer, A3/LD)  200±0.5 mm (0.1 mm/step)
D: 05-4402 (2nd drawer, A3/LD)  52±0.5 mm (0.10 mm/step)
05-4058 (1st drawer, A4/LT)
05-4059 (2nd drawer, A3/LD)
05-4060 (3rd drawer, A4/LT)
05-4560 (4th drawer, A4/LT)
05-4061 (Bypass feed, A4/LT)
05-4062 (Duplex feeding, A3/LD)
05-4561 (Tandem LCF, A4/LT)
05-4063 (Option LCF, A4/LT)
E: 05-4019-0 (2nd drawer, A3/LD),  52±0.5 mm (0.04 mm/step)
05-4019-1 (1st drawer, A4/LT)
05-4019-2 (A4-R/LT-R)