NETGEAR ProSafe GSM7224P User Manual

350 East Plumeria Drive
San Jose, CA 95134
USA
November 2011
202-10936-01
1.0
ProSafe Managed Switch
Command Line Interface (CLI)
User Manual
9.0.2
GSM5212P
GSM7212F
GSM7212P
GSM7224P
XSM7224S

NETGEAR ProSafe GSM7224P Specifications

General

Brand	NETGEAR
Model	ProSafe GSM7224P
Category	Switch
Language	English

Summary

Chapter 1 Using the Command-Line Interface

Licensing and Command Support

Command Syntax

Explains the structure of commands, including keywords, required, and optional parameters.

Command Modes

Explains different CLI command modes, their prompts, and descriptions.

CLI Error Messages

Accessing the CLI

Explains how to access the CLI via console or remote connections.

Chapter 2 Stacking Commands

Dedicated Port Stacking

Describes commands to configure dedicated port stacking.

Non-Stop Forwarding Commands

Stack Firmware Synchronization Commands

Chapter 3 Switching Commands

Port Configuration Commands

Describes commands to view and configure port settings.

Spanning Tree Protocol (STP) Commands

Describes commands to configure Spanning Tree Protocol (STP).

VLAN Commands

Describes commands to configure VLAN settings.

Port-Based Network Access Control Commands

Describes commands to configure port-based network access control (802.1x).

802.1X Supplicant Commands

Describes 802.1X supplicant functionality on point-to-point ports.

Storm-Control Commands

Describes commands to configure storm-control and view storm-control configuration.

Port-Channel/LAG (802.3ad) Commands

Describes commands to configure port-channels, also known as link aggregation groups (LAGs).

Static MAC Filtering

Describes commands to configure static MAC filtering.

DHCP Snooping Configuration Commands

Describes commands to configure DHCP Snooping.

Dynamic ARP Inspection Commands

Describes Dynamic ARP Inspection (DAI) as a security feature.

Chapter 4 Multicast VLAN Registration (MVR)

MVR Commands

Chapter 5 Routing Commands

Address Resolution Protocol (ARP) Commands

Describes commands to configure ARP and view ARP information on the switch.

IP Routing Commands

Describes commands to enable and configure IP routing on the switch.

Virtual Router Redundancy Protocol Commands

Describes commands to view and configure Virtual Router Redundancy Protocol (VRRP).

DHCP and BOOTP Relay Commands

Describes commands to configure BootP/DHCP Relay on the switch.

IP Helper Commands

Describes commands to configure a DHCP relay agent with multiple DHCP server addresses.

Open Shortest Path First (OSPF) Commands

Describes commands to view and configure OSPF.

OSPF Graceful Restart Commands

Chapter 6 IP Multicast Commands

Multicast Commands

PIM Commands

Describes Protocol Independent Multicast (PIM) commands for IPv6.

Internet Group Message Protocol (IGMP) Commands

Describes commands to view and configure IGMP settings.

Chapter 7 IPv6 Commands

IPv6 Routing Commands

Describes IPv6 commands to configure IPv6 on the system and interfaces.

OSPFv3 Commands

Describes commands to configure OSPFv3, a link-state routing protocol.

OSPFv3 Graceful Restart Commands

DHCPv6 Commands

Describes commands to configure the DHCPv6 server and view DHCPv6 information.

Chapter 8 IPv6 Multicast Commands

IPv6 Multicast Forwarder Commands

Describes mroute entries specific for IPv6.

IPv6 PIM Commands

Describes PIM commands that support the PIM version of IPv6.

IPv6 MLD Commands

Describes commands used for MLD Snooping in IPv6.

Chapter 9 Quality of Service (QoS) Commands

Class of Service (CoS) Commands

Describes commands to configure and view Class of Service (CoS) settings.

Differentiated Services (DiffServ) Commands

Describes commands to configure QOS Differentiated Services (DiffServ).

DiffServ Class Commands

Describes DiffServ class commands to define traffic classification.

DiffServ Policy Commands

Describes DiffServ policy commands to specify traffic conditioning actions.

DiffServ Service Commands

Describes DiffServ service commands to assign a DiffServ traffic conditioning policy.

Chapter 10 Power over Ethernet (PoE) Commands

PoE Commands

Describes commands to enable or disable Power over Ethernet (PoE) functionality.

Chapter 11 Utility Commands

Logging Commands

Describes commands to configure system logging and view logs.

System Utility and Clear Commands

DHCP Server Commands

Serviceability Packet Tracing Commands

Chapter 12 Management Commands

Configuring the Switch Management CPU

Network Interface Commands

Console Port Access Commands

Secure Shell (SSH) Commands

Management Security Commands

Hypertext Transfer Protocol (HTTP) Commands

User Account Commands

SNMP Commands

RADIUS Commands

TACACS+ Commands

IPv6 Management Commands

Chapter 13 Log Messages

Chapter 14 Captive Portal Commands

Captive Portal Global Commands

Captive Portal Configuration Commands

Captive Portal Client Connection Commands

Captive Portal Interface Commands

Captive Portal Local User Commands