EasyManuals Logo
Home>Fujitsu>Server>Oracle SPARC M12-2

Fujitsu Oracle SPARC M12-2 User Manual

Fujitsu Oracle SPARC M12-2
560 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #30 background imageLoading...
Page #30 background image
Caution
-
Observe
the
precautions
shown
below
to
ensure
the
safety
of
the
system.
1.6 Other
Precautions
â– 
The
printed
circuit
boards
in
the
SPARC
M12-2/M12-2S
can
be
easily
damaged
by
static
electricity.
To
prevent
damage
to
the
printed
circuit
boards,
wear
a
wrist
strap,
and
connect
it
to
the
chassis
prior
to
starting
maintenance.
â– 
When
mounting
any
unit
in
the
SPARC
M12-2/M12-2S,
check
the
connectors
beforehand
to
confirm
that
none
of
the
pins
are
bent
and
that
all
the
pins
are
neatly
arranged
in
lines.
If
a
unit
is
mounted
with
a
bent
pin
in
a
connector,
the
SPARC
M12-2/M12-2S
may
be
damaged.
When
mounting
a
component,
perform
the
work
carefully
so
as
not
to
bend
any
pins.
â– 
If
excessive
force
is
applied
to
a
CPU
memory
unit,
the
units
mounted
on
printed
circuit
boards
may
be
damaged.
When
handling
a
CPU
memory
unit,
observe
the
following
precautions.
-
Hold
the
CPU
memory
unit
by
the
metal
frame.
-
When
holding
the
CPU
memory
unit,
keep
it
horizontal
until
you
lay
it
on
the
cushioned
ESD
mat.
-
The
CPU
memory
unit
consists
of
printed
circuit
boards
connected
with
thin
connection
pins.
Therefore,
do
not
place
the
CPU
memory
unit
on
a
hard
surface.
-
Be
careful
not
to
damage
the
components
located
on
either
side
of
the
CPU
memory
unit.
â– 
The
heat
sinks
can
be
damaged
by
incorrect
handling.
Do
not
touch
the
heat
sinks
while
replacing
or
removing
a
CPU
memory
unit.
If
a
heat
sink
is
disconnected
or
otherwise
damaged,
obtain
a
replacement
CPU
memory
unit.
When
storing
or
carrying
a
CPU
memory
unit,
ensure
that
the
heat
sinks
are
sufficiently
protected.
â– 
When
removing
a
cable
such
as
a
LAN
cable,
if
you
cannot
reach
the
latch
lock
of
the
connector,
use
a
flathead
screwdriver,
etc.
to
push
the
latch
and
release
the
cable.
If
you
use
force
to
remove
the
cable,
the
LAN
port
of
the
CPU
memory
unit
or
the
PCI
Express
card
may
be
damaged.
â– 
Do
not
use
any
power
cords
other
than
those
specified.
â– 
Check
the
appearance
of
the
products
before
starting
work.
When
unpacking
them,
confirm
that
no
unit
is
deformed,
no
connector
is
damaged,
and
there
are
no
other
such
defects.
Do
not
mount
the
products
that
have
a
defect
in
the
appearance.
Mounting
a
product
that
has
a
defect
in
appearance
may
damage
the
SPARC
M12-2/M12-2S.
Fujitsu
SPARC
M12-2/M12-2S
Service
Manual
ï½¥
January
20238

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu Oracle SPARC M12-2 and is the answer not in the manual?

Fujitsu Oracle SPARC M12-2 Specifications

General IconGeneral
BrandFujitsu
ModelOracle SPARC M12-2
CategoryServer
LanguageEnglish

Related product manuals