EasyManuals Logo

Fujitsu Oracle SPARC M12-2 User Manual

Fujitsu Oracle SPARC M12-2
560 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #47 background imageLoading...
Page #47 background image
Table
2-11
　　
System
Operation
Modes
Icon Operation
Mode Description
Locked
mode -
Pressing
of
the
POWER
switch
　
Starts
the
system.
-
Break
signal
　
Depends
on
the
operation
mode
(break_signal)
set
for
the
physical
partition
(*1).
Service
mode -
Pressing
of
the
POWER
switch
Stops
the
system
when
done
for
4
seconds
or
more.
-
Break
signal
Valid
regardless
of
the
operation
mode
(break_signal)
set
for
the
physical
partition
(*1).
*1
Use
the
setpparmode
command
to
set
the
operation
mode
for
the
physical
partition.
For
details,
see
the
Fujitsu
SPARC
M12
and
Fujitsu
M10/SPARC
M10
XSCF
Reference
Manual
of
the
XCP
version
used.
Table
2-12
　　
Functions
of
the
Power
Switch
Icon POWER
Switch
Pressing
Time
Operation
Mode
Description
1
second
or
more
and
less
than
4
seconds
Locked
mode
The
system
starts
when
it
is
stopped.
If
a
power-on
wait
time
and
warm-up
time
for
the
air
conditioning
facilities
are
set
in
the
XSCF,
the
power-on
time
and
warm-up
completion
wait
time
for
the
air
conditioning
facilities
are
omitted.
The
operation
is
invalid
when
the
system
is
in
operation.
The
system
does
not
react
if
the
POWER
switch
is
pressed.
Service
mode
The
operation
is
invalid,
regardless
of
the
operation
status
of
the
system.
The
system
does
not
react
if
the
POWER
switch
is
pressed.
There
are
two
system
operation
modes,
Locked
and
Service.
The
mode
can
be
switched
as
appropriate
for
the
system
status.
Set
the
Locked
mode
when
the
system
is
in
operation
and
the
Service
mode
for
system
maintenance.
In
a
building
block
configuration
where
two
or
more
SPARC
M12-2S
units
are
connected,
set
the
same
operation
mode
for
both
the
SPARC
M12-2S
unit
of
the
master
XSCF
and
that
of
the
standby
XSCF.
Table
2-11
describes
the
major
differences
in
system
operations
between
the
operation
modes.
For
information
on
system
operations
other
than
those
described
in
Table
2-11,
see
"Chapter
13
Switching
to
Locked
Mode/Service
Mode"
in
the
Fujitsu
SPARC
M12
and
Fujitsu
M10/SPARC
M10
System
Operation
and
Administration
Guide.
Use
the
POWER
switch
to
start
or
stop
the
system.
The
system
starts
or
stops
differently
depending
on
how
the
POWER
switch
is
pressed
and
the
system
operation
mode.
Table
2-12
describes
how
the
system
starts
or
stops
differently
depending
on
how
the
POWER
switch
is
pressed.
Chapter
2
　
Understanding
the
System
Units 25

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu Oracle SPARC M12-2 and is the answer not in the manual?

Fujitsu Oracle SPARC M12-2 Specifications

General IconGeneral
BrandFujitsu
ModelOracle SPARC M12-2
CategoryServer
LanguageEnglish

Related product manuals