Why is there low voltage and the battery won't charge on my MacDon M1170 Farm Equipment?
If you're experiencing low voltage or the battery isn't charging on your MacDon Farm Equipment, start by having the battery tested. Clean and tighten the battery connections. Replace the alternator belt if it is defective. Ensure the alternator or voltage regulator are properly connected.
What causes high oil consumption in MacDon M1170?
High oil consumption in your MacDon Farm Equipment can be due to several reasons. Ensure you are using the recommended oil. Also, check for oil leaks around gaskets, seals, and drain plugs.
How to stop excessive noise from the MacDon Farm Equipment drive system?
To address excessive noise from the drive system of your MacDon Farm Equipment, first, remove any mechanical interference in the steering or ground speed linkage. Check the charge pressure if the brakes are binding or not releasing fully. Inspect the lines for leakage if there is air in the system. Tighten the hydraulic line clamps if they are loose, and replace worn ball joints.
What causes low oil pressure in MacDon Farm Equipment?
If your MacDon Farm Equipment has low oil pressure, first add oil if the oil level is low. If the oil level is adequate, drain and fill the crankcase with the proper oil.
Why isn't the air conditioning cooling in my MacDon Farm Equipment?
If the air conditioning in your MacDon Farm Equipment isn't cooling, start by adding refrigerant if the level is low. Replace the thermostat if the switch contacts are burned or the sensing element is defective. Clean the condenser if the fins are plugged.
How to fix MacDon M1170 Farm Equipment if it will not steer straight?
If your MacDon Farm Equipment will not steer straight, adjust the steering chain tension, replace worn parts, and adjust the linkage.
How to adjust steering if it is too stiff on MacDon Farm Equipment?
If the steering on your MacDon Farm Equipment is too stiff or too loose, adjust the steering chain tension.
What should I do if the hydraulic oil high-temperature alarm activates on my MacDon Farm Equipment?
If the hydraulic oil high-temperature alarm activates on your MacDon Farm Equipment, check and clean the cooling box.
Why are the lights dim on my MacDon Farm Equipment?
If the lights are dim on your MacDon Farm Equipment, check the wiring circuit for a break in a wire or a poor ground.
Indicates important safety messages in this manual and on safety signs on the machine.
Uses DANGER, WARNING, and CAUTION to alert you to hazardous situations.
Provides general farm safety precautions for operating machinery, including personal protective equipment.
Ensures safety while performing maintenance, including following good shop practices.
Provides safety guidelines for working with hydraulic systems, including leak testing.
Offers safety precautions for servicing tires, including inflation procedures.
Details safety precautions when working near batteries, including spark prevention.
Emphasizes correct procedures for welding to avoid damage to electronics.
Provides safety guidelines for engine operation, including starting and potential hazards.
Information on keeping safety signs clean, legible, and replacing missing or illegible ones.
Illustrations and table identifying the locations of various safety signs on the machine.
Detailed explanation of specific safety signs and their associated warnings.
Lists and defines terms and acronyms used throughout the manual.
Details technical specifications for the M1170 Windrower's engine, electrical system, and traction drive.
Provides key dimensions and measurements of the windrower with diagrams.
Identifies major components of the windrower with front and rear views.
Describes the controls and amenities located on the operator's console.
Details the safety feature that deactivates systems when the operator is not seated.
Explains how to adjust various features of the operator's seat for comfort.
Provides instructions for adjusting the steering column and steering wheel.
Describes the operation of various lights, including cab-forward and engine-forward modes.
Details the ignition switch, throttle, and Harvest Performance Tracker display controls.
Explains the operation of various header controls on the console and GSL handle.
Describes the HPT screen layout and how to adjust settings.
Outlines the user's responsibilities for safe operation and manual adherence.
Defines symbols used to depict functions or reactions of instruments and controls.
Covers operational safety, break-in period, daily checks, and engine start procedures.
Provides procedures for attaching and detaching various header types to the windrower.
Details how to navigate menus to check and adjust header settings.
Explains header operation, including safety props, float, drive, angle, and cutting height.
Provides specific instructions for operating D1X/D1XL Series Draper Headers.
Details operation procedures for the A40DX Auger Header, including reel/auger and knife speeds.
Covers operation of R1 Series Rotary Disc Headers, including disc speed and float options.
Details recommended specifications for fuel, fluids, lubricants, and system capacities.
Outlines periodic maintenance procedures and service intervals to maximize machine life.
Covers procedures for opening and closing the engine hood.
Details procedures for opening, closing, adjusting, and accessing the platform.
Provides overviews for DEF system, cooling system, air intake, hydraulic, and electrical systems.
Lists specific procedures for break-in inspections, including torque values for nuts.
Details daily maintenance tasks, including checks for fluids, tires, and hoses.
Specifies maintenance tasks required every 50 hours, such as cleaning filters and greasing.
Outlines maintenance tasks for every 100 hours of operation, including filter cleaning.
Details maintenance tasks for every 250 hours or annually, including oil and filter changes.
Covers maintenance tasks for every 500 hours or annually, including fuel and hydraulic filters.
Specifies maintenance tasks for every 1000 hours, including fuel tank vent filter.
Details maintenance tasks for every 2000 hours, including engine coolant change.
Lists annual maintenance tasks recommended prior to the operating season.
Covers service procedures that should be performed as needed, like seat belt checks.
Information on the High Debris Cooler Intake (Hood Scoops) kit.
Details automated steering systems and high performance lighting options for the cab.
Covers operation of headers, including booster spring kits and double windrow attachments.
Provides information on ballast, towing harness, and weight box for transport.
Lists common engine problems and their solutions, such as starting issues.
Addresses issues related to low voltage, dim or non-functional lights, and wiring problems.
Covers problems with the hydraulic system, such as lifting issues and temperature alarms.
Details troubleshooting steps for header drive engagement, power loss, and alarms.
Addresses issues with the traction drive system, including alarms and wheel performance.
Covers problems with steering alignment, ground speed control, and stiffness.
Details issues with the cab air system, including blower, heater, and air conditioning problems.
Addresses issues related to operator's station comfort, such as rough ride.
Provides correct torque values for various bolts, cap screws, and hydraulic fittings.
Details metric bolt specifications for different grades and materials.
Instructions for installing and torquing adjustable O-ring boss hydraulic fittings.
Instructions for installing and torquing non-adjustable O-ring boss hydraulic fittings.
Procedure for assembling O-ring face seal hydraulic fittings.
Guidance for assembling pipe thread fittings, including sealant and torque.
Provides conversion factors between SI units and US customary units.
Lists windrower fault codes, including source address, SPN, FMI, and descriptions.
General| Brand | MacDon |
|---|---|
| Model | M1170 |
| Category | Farm Equipment |
| Language | English |
To Next Page
