SmartAXIS Touch User’s Manual Preface-2
SAFETY PRECAUTIONS
• Prevent the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and FT1A-*14SA-* from falling while moving or
transporting, otherwise damage or malfunction of the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and
FT1A-*14SA-* will result.
• Use the product within the environmental limits given in the catalog and manual. Use of the product in high-
temperature or high-humidity environments, or in locations where it is exposed to condensation, corrosive gas
or large shock loads can create the risk of electrocution and fire.
• The SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and FT1A-*14SA-* are designed for use in pollution degree 2.
Use the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and FT1A-*14SA-* in environments of pollution degree 2.
(based on the IEC60664-1 rating)
• Install the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and FT1A-*14SA-* according to the instructions. Improper
installation will result in falling, failure, electrical shock, fire hazard, or malfunction of the SmartAXIS FT1A-*12RA-*,
FT1A-*14KA-* and FT1A-*14SA-*.
• Prevent metal fragments or wire chips from dropping inside the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and
FT1A-*14SA-* housing. Ingress of such fragments and chips may cause fire hazard, damage, and malfunction.
• Use a power supply of the rated value. Using a wrong power supply may cause fire hazard.
• The SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and FT1A-*14SA-* uses “PS2 of EN61131” as DC power supply.
(based on the IEC/EN61131 rating)
• Use wire of a proper size to meet the voltage and current requirements.
• Use an IEC 60127-approved fuse on the output circuit and the power line outside the FT1A-*12RA-*, FT1A-*14KA-* and
FT1A-*14SA-*. This is required when equipment containing the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and
FT1A-*14SA-* is destined for Europe.
• Use an EU-approved circuit breaker. This is required when equipment containing the SmartAXIS FT1A-*12RA-*,
FT1A-*14KA-* and FT1A-*14SA-* is destined for Europe.
• Make sure of safety before starting and stopping the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and
FT1A-*14SA-*. Incorrect operation of the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and FT1A-*14SA-* may
cause mechanical damage or accidents.
• Use the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and FT1A-*14SA-* in a local area network if you download or
upload the project data via the Ethernet port.
• The touch panel of the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and FT1A-*14SA-* is made of glass, and will
break if exposed to excessive shock. Take due care when handling it.
• When more than one button is pressed at the same time, due to the detection characteristics of an analog type
touch panel, only the gravity center of the pressed area is sensed and the unit assumes that only one button is
pressed. Thus, when more than one button is pressed simultaneously, the resulting operation is not guaranteed.
• The screen becomes blank when the backlight is burnt out; however, the touch panel remains enabled. Incorrect
touch panel operation will occur when operating the touch panel when the backlight appears to be turned off
but is actually burnt out. Note that this erroneous operation may result in damage.
• Do not push hard or scratch the touch panel and protection sheet with a hard object such as a tool, because
they are damaged easily.
• At temperatures over the rated operating temperature, the clock accuracy is affected. Adjust the clock before use.
• For applications which require clock accuracy, adjust the clock periodically.
• Do not install the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and FT1A-*14SA-* in areas subjected to strong
ultraviolet rays, since ultraviolet rays may impair the quality of the LCD.
• Do not attempt to disassemble, repair or modify the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and
FT1A-*14SA-*. This can create the risk of fire or electrocution.
• When disposing of the SmartAXIS FT1A-*12RA-*, FT1A-*14KA-* and FT1A-*14SA-*, do so as an industrial
waste.
• Do not switch off the power or pull out the USB flash drive while it is being accessed, as this may result in
destruction of the stored data. If the data on the USB flash drive is corrupted, format the USB flash drive.
To Next Page
Loading...
Need help?
General
