838
DELAY
L Delay Time [msec] [0.0…1360.0]
Sets the delay time for the left channel.
R Delay Time [msec] [0.0…1360.0]
Sets the delay time for the right channel.
Feedback [+/–100]
Sets the feedback amount.
High Damp [%] [0…100]
This controls the high-frequency attenuation in the feedback
loop. See “High Damp [%]” on page 833.
Low Damp [%] [0…100]
This controls the low-frequency damping in the feedback
loop. See “Low Damp [%]” on page 833.
Spread [+/–100]
Sets the width of the stereo image of the effect sound. For
more information, see “Spread” on page 833.
OUTPUT
This is the standard effects output section, with modulatable
control over wet/dry balance. For more information, see
“OUTPUT” on page 762.
084: Stereo Auto Panning Delay
This stereo delay effect pans the delay sound left and right
using the LFO.
DELAY
L Delay Time [msec] [0.0…1360.0]
Sets the delay time for the left channel.
R Delay Time [msec] [0.0…1360.0]
Sets the delay time for the right channel.
L Feedback [+/–100]
Sets the feedback amount for the left channel.
R Feedback [+/–100]
Sets the feedback amount for the right channel.
High Damp [%] [0…100]
This controls the high-frequency attenuation in the feedback
loop. See “High Damp [%]” on page 833.
Low Damp [%] [0…100]
This controls the low-frequency damping in the feedback
loop. See “Low Damp [%]” on page 833.
LFO
Waveform [Triangle, Sine]
Selects the LFO Waveform.
Shape [+/–100]
Changes the curvature of the LFO Waveform. See “Shape”
on page 782.
Phase [degrees] [–180…+180]
Sets the LFO phase difference between the left and right. See
“Phase [degrees]” on page 817.
Frequency [Hz] [0.02…20.00]
This sets the LFO speed, in Hz. It applies only when
MIDI/Tempo Sync, below, is Off.
MIDI/Tempo Sync [Check-box]
BPM [MIDI, 40.00…300.00]
Base Note [ … ]
Times [x1…x32]
When MIDI/Tempo Sync is on, the LFO speed is set by
BPM, Base Note, and Times, instead of Frequency. For
more information, see “MIDI/Tempo Sync” on page 779.
Type [Individual, Common1, Common2]
This controls whether the effect uses its individual LFO, or
one of the Common FX LFOs. For more information, see
“LFO Type” on page 779.
Common LFO Phase Offset [degrees] [+/–180]
When Type is set to Common FX LFO 1 or 2, this lets you
offset the phase from the master LFO.
AUTO PAN
Depth [0…100]
Sets the panning width.
Source [Off…Tempo]
Selects the modulation source for the panning width.
Amount [+/–100]
Set the modulation amount of the panning width.
OUTPUT
This is the standard effects output section, with modulatable
control over wet/dry balance. For more information, see
“OUTPUT” on page 762.
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
LFO Phase
LFO Shape
Pan
Pan
LFO: Tri / Sin
Depth
Delay
Delay
High Damp Low Damp
High Damp
Low Damp
Feedback
To Next Page
Loading...
Need help?
General
