Korg NAUTILUS Series

876
Mono/Mono Parallel
141: P4EQ // P4EQ through 185: Mt.BPM Dly//Mt.BPM
Dly are parallel effects, with the left input going through one
effect, and the right going through the other. These provide
various combinations of 4-band EQ, Compressor, Limiter,
Exciter, Overdrive, Wah, Chorus/Flanger, Phaser, and
Multitap Delay, as described below.
4 band EQ
For a description of the on-screen EQ graphic, see “011:
Stereo Parametric 4EQ” on page 774.
PARAMETRIC EQ
Trim [0…100]
Sets the input level.
Band1 Fc [Hz] [20…1.00k]
Sets the center frequency of Band 1.
Q [0.5…10.0]
Sets the bandwidth of Band 1. See “Q” on page 774.
Gain [dB] [–18.0…+18.0]
Sets the gain of Band 1.
Band2 Fc [Hz] [50…5.00k]
Sets the center frequency of Band 2.
Q [0.5…10.0]
Sets the bandwidth of Band 2. See “Q” on page 774.
Gain [dB] [–18.0…+18.0]
Sets the gain of Band 2.
Band3 Fc [Hz] [300…10.00k]
Sets the center frequency of Band 3.
Q [0.5…10.0]
Sets the bandwidth of Band3. See “Q” on page 774.
Gain [dB] [–18.0…+18.0]
Sets the gain of Band 3.
Band4 Fc [Hz] [500…20.00k]
Sets the center frequency of Band 4.
Q [0.5…10.0]
Sets the bandwidth of Band 4. See “Q” on page 774.
Gain [dB] [–18.0…+18.0]
Sets the gain of Band 4.
OUTPUT
Pan [L000…C064…R127]
Sets the stereo image.
Wet/Dry [Dry, 1:99…99:1, Wet]
Sets the balance between the effect and the dry input.
Source [Off…Tempo]
Selects a modulation source for Wet/Dry.
Amount [+/–100]
Sets the modulation amount for Wet/Dry.
Compressor
For details on the Compressor graphics, see “001: Stereo
Dyna Compressor” on page 761.
Pre EQ
Trim [0…100]
Sets the EQ input level.
LEQ Gain [dB] [–15…+15]
Sets the gain of the Low EQ.
HEQ Gain [dB] [–15…+15]
Sets the gain of the High EQ.
COMPRESSOR
Sensitivity [1…100]
Sets the sensitivity. See “Sensitivity” on page 761.
Attack [1…100]
Sets the attack level. See “Attack” on page 762.
Output Level [0…100]
Sets the output level.
OUTPUT
Pan [L000…C064…R127]
Sets the stereo image.
Wet/Dry [Dry, 1:99…99:1, Wet]
Sets the balance between the effect and the dry input.
Source [Off…Tempo]
Selects a modulation source for Wet/Dry.
Amount [+/–100]
Sets the modulation amount for Wet/Dry.
Limiter
For details on the Limiter graphics, see “005: Stereo
Limiter” on page 768.
LIMITER
Ratio [1.0:1…50.0:1, Inf:1]
Sets the signal compression ratio. See “Ratio” on page 763.
Threshold [dB] [–40…0]
Sets the level above which the compressor is applied. See
“Threshold [dB]” on page 763.
Attack [1…100]
Sets the attack time. See “Attack [msec]” on page 764.
Release [1…100]
Sets the release time. See “Release [msec]” on page 764.