Korg NAUTILUS Series Parameter Guide

PROGRAM mode: HD-1
24
Source Bus = USB 1/2
Source Bus = Indiv. 1/2
Source Direct Solo [Off, On]
This selects what is heard through the L/R outputs and
headphones when Sampling REC is enabled.
On (checked): Only the signal of the selected Source Bus
will be heard. This lets you hear only the sound that will be
sampled.
Off (unchecked): The signal of the selected Source Bus
will be merged with the main L/R signal. This is the default.
Note: If Source Bus is set to L/R, this setting is ignored–
since that signal is normally heard at the L/R outputs
already!
Trigger [Sampling START Button, Note On]
Specifies how sampling will be initiated.
Sampling START Button: Pressing the SAMPLING REC
button will cause the NAUTILUS to enter sampling-standby
mode, and sampling will begin when you press the
SAMPLING START/STOP button.
Note On: Press the SAMPLING REC button and then press
the SAMPLING START/STOP button to enter sampling-
standby mode. Sampling will begin when you play the
keyboard.
Sampling will also begin if a MIDI note-on is received
(instead of playing the keyboard).
Regardless of the settings you’re using, press the
SAMPLING START/STOP button once again when you’ve
finished sampling. Alternatively, sampling will end
automatically if the specified “Sampling Time” elapses.
Metronome Precount [Off, 4, 8, 3, 6]
This specifies whether the metronome will sound a count-
down before sampling begins. This can be set only if
“Trigger” is set to Sampling START button.
Off: Sampling will begin immediately when you press the
SAMPLING START/STOP button from recording-standby
mode.
4, 8, 3, 6: When you press the SAMPLING START/STOP
button from recording-standby mode, the metronome will
count the specified number of beats at the system tempo, and
then sampling will begin. If you set this to 4, sampling will
begin on the count of 0 after a pre-count of 4–3–2–1–0.
The output destination and level of the metronome sound are
specified by Metronome Setup (0–8d). If “Output Bus” is set
to L/R, the metronome will stop sounding the instant
sampling actually begins.
Sample to Disk [16-bit, 24-bit]
This sets the bit depth for sampling to media. Note that this
does not affect sampling to RAM. This same parameter
appears on the sampling setup pages in Program,
Combination, Sequencer, and SAMPLING modes; changes
in one place are reflected everywhere.
L-Mono
R-Mono
Stereo
Level Pan
Insert
Eects
CLIP !!
L/MONO
R
AUDIO OUTPUT
HEADPHONES
Insert
Eects
L/R
Bus
REC
1/2
REC
3/4
Bus = L/R or IFX1-12
Level Pan
Insert
Eects
OSC
USB-B 1 (L)
USB-B 2 (R)
Source Bus = USB 1/2
[x] Source Direct Solo
Total
Eects
Master
Eects
Sampling
Monitor
1/2
3/4
Indiv.
L-Mono
R-Mono
Stereo
Level Pan
Insert
Eects
CLIP !!
L/MONO
R
AUDIO OUTPUT
HEADPHONES
Insert
Eects
L/R
Bus
REC
1/2
REC
3/4
INDIV.1
INDIV.2
AUDIO OUTPUT
Bus = Indiv.1/2 or IFX1-12
Audio Input
OSC
[x] Source Direct Solo
Source Bus = Indiv.1/2
Total
Eects
Master
Eects
Sampling
Monitor
1/2
3/4
Indiv.

Korg NAUTILUS Series Specifications

General

Sampling	Open Sampling System
MIDI	In, Out, Thru
Preset Combinations	384
Keyboard	61-key (NAUTILUS 61), 73-key (NAUTILUS 73), 88-key (NAUTILUS 88, RH3 weighted action)
Effects	12 Insert Effects; 2 Master Effects; 2 Total Effects
Sequencer	16-track MIDI Sequencer
Storage	Internal SSD (60 GB)
Audio Inputs	2 x 1/4"
Audio Outputs	Headphones
USB	Type A (host), Type B (device)
Weight	NAUTILUS 88: 23.1 kg
Display	8 inch TouchView™ GUI (800x600 pixels)