Korg NAUTILUS Series Parameter Guide

SEQUENCER mode
452
Indiv.1…4 (mono), Indiv.1/2…3/4 (stereo): The Indiv.1/2–
Indiv.3/4 output buses will be recorded. Similarly to when
using the REC buses, you can choose this when you want to
monitor the L/R output while recording only the audio input.
For more information, see the diagram “REC Source = Indiv.
1, 2 (3, 4).”
If Stereo Pair is on and you’ve selected Indiv.1/2, the Indiv.
bus 1 will be sent to odd-numbered tracks, and Indiv. bus 2
will be sent to even-numbered tracks.
STEREO
This is shown if Stereo Pair is on.
Play/Rec/Mute [Play, Rec, Mute]
Use this to mute an audio track, or to select the recording
tracks for multi-track recording. During playback, or for
single-track recording (normal recording), it is possible only
to select Play or Mute for tracks (playback tracks) other than
the recording track. For multi-track recording, tracks can be
set to Play, Rec, or Mute. The setting will alternate each time
you press the Play/Rec/Mute button.
Play: The track will play.
Rec: This will be displayed during single-track recording
(normal recording). It cannot be selected.
When you use multi-track recording (the Preferences page
“Multi REC” is on), select REC for the tracks that you wish
to record. You can specify REC for up to four tracks.
Mute: The track will be muted (silent).
Solo On/Off [On, Off]
This turns the Solo function on/off.
Only tracks that are set to Solo On will sound. Other tracks
will be muted.
The setting will alternate on/off each time you press the Solo
button.
The operation will depend on the setting of the Exclusive
Solo menu command, as described below:
Exclusive Solo off: Multiple tracks can be soloed. The solo
setting of each track will change each time you press its Solo
On/Off button.
Exclusive Solo on: When you press a Solo On/Off button,
only that track will be soloed.
Note: The Solo function applies to MIDI tracks 1–16, audio
tracks 1–16, and audio inputs 1–2.
Solo settings are not saved with the song.
0–1c: Volume
Recording Audio Track Pan and Volume
The pan and volume that you specify here will be used when
you playback or record from the beginning of the song. If
you modify these settings while recording, your changes will
be recorded as automation event data on the automation
track for each audio track, and the pan and volume data will
change accordingly during playback. You can also change
the settings during playback. However when the song
reaches a location where pan or volume data was recorded,
the settings will change accordingly.
Pan [L000…C064…R127]
This specifies the pan of audio track.
L000…C064…R127: L000 is hard left, and R127 is hard
right.
If a mono insert effect is in use, the settings you make here
will be ignored. In this case, the “Pan (CC#8)” parameter in
IFX– Insert FX page will adjust the panning of the sound
after the Insert Effect. For details, see “Mixer” on page 746.
For paired audio tracks, the above parameters are
controlled by the odd-numbered audio track.
These parameters will not be controlled if you edit the
even-numbered audio track.
If, however, in the Stereo Pair page menu command you
set “Pan Mode” to Index, the Pan of the even-numbered
audio track will be valid.
Volume [000…127]
This fader adjusts the volume of the Audio Track. The meter
to the left of the fader displays its audio level in realtime.
For paired audio tracks, the above parameters are
controlled by the odd-numbered audio track.
These parameters will not be controlled if you edit the
even-numbered audio track.
Insert
Eects
L/R
Bus
REC
1,2, 3, 4
INDIV.1
INDIV.2
AUDIO OUTPUT
REC Source
= Indiv.1, 2 (3, 4)
CLIP !
Recording (Multi REC)
Bus = L/R or IFX1-12
Insert
Eects
LevelPan
HDR Track (Mono)
HDR Track (Mono)
Indiv.1
Indiv.2
REC Source
Indiv.
1,2,3,4
Set Play/Rec/Mute
to Rec
Sequencer Playback
Keyboard
Bus = L/R or IFX1-12
L/MONO
R
AUDIO OUTPUT
HEADPHONES
[x] Source Direct Solo
Total
Eects
Master
Eects
Monitor
If the Bus Select of an audio track is set to Indiv. 1 or 2, the Rec input will
automatically be muted in order to avoid a feedback loop. If you route the signal
to IFX, the same thing will occur if you send the post-IFX signal to REC Bus 1 or 2.

Korg NAUTILUS Series Specifications

General

Sampling	Open Sampling System
MIDI	In, Out, Thru
Preset Combinations	384
Keyboard	61-key (NAUTILUS 61), 73-key (NAUTILUS 73), 88-key (NAUTILUS 88, RH3 weighted action)
Effects	12 Insert Effects; 2 Master Effects; 2 Total Effects
Sequencer	16-track MIDI Sequencer
Storage	Internal SSD (60 GB)
Audio Inputs	2 x 1/4"
Audio Outputs	Headphones
USB	Type A (host), Type B (device)
Weight	NAUTILUS 88: 23.1 kg
Display	8 inch TouchView™ GUI (800x600 pixels)