SEQUENCER: Page Menu Commands Copy Measure
543
3. In From Measure and To End of Measure, specify the
range of measures that will be repeated.
By default, the range of measures will be set as specified
on the Track Edit page.
4. In Times, specify the number of repetitions.
For example if you set From Measure to 001, To End of
Measure to 004, and Times to 2, the musical data of
measures 1–4 will be inserted into measures 5–8. The
result will be that measures 1–4 will be played twice.
5. Specify the track(s) for which you want to execute the
command.
If you execute with All Tracks, All MIDI Tracks, and
All Audio Tracks unchecked, the playback data will be
inserted into the track that’s selected in Track Select. Be
aware that at this time, the playback data that follows the
inserted location will move toward the end of the song
according to the number of inserted measures, but the
time signature and tempo will not move.
If you check All Tracks, the playback data will be
inserted into all tracks including the Master Track. The
playback data in subsequent measures will play just as it
did before this command was executed.
If you check All MIDI Tracks (when a MIDI track is
selected), the data will be inserted into all MIDI tracks.
If you check All Audio Tracks (when an Audio track is
selected), the data will be inserted into all audio tracks.
6. To execute the Repeat Measure command, press the
OK button. To cancel, press the Cancel button.
If you execute Repeat Measure at a location in the middle
of an audio event that spans several measures, a new
region will be automatically created and named.
Note: The WAVE file itself will not be modified.
Copy Measure
This command copies the measures of musical data specified
as the “From” source to the beginning of the measure
specified as the “To” location.
When you execute the Copy Measure command, the existing
track data at the copy destination will be rewritten.
1. Select the copy source song.
2. Select “Copy Measure” to open the dialog box.
MIDI tracks
Audio tracks
3. Use From: Track or “Audio Track” to select the copy-
source track.
(By default, this will be the Track Select track.)
If you execute with All Tracks, All MIDI Tracks, and
All Audio Tracks unchecked, only the selected track will
be copied. Note that the time signature and tempo will not
be copied.
If you check All Tracks, the playback data of all tracks
including the Master Track will be copied.
If you check All MIDI Tracks (when a MIDI Track is
selected), all MIDI tracks will be copied.
If you check All Audio Tracks (when an Audio Track is
selected), all audio tracks will be copied.
4. In From Measure and To End of Measure, specify the
range of copy source measures.
By default, the range of measures will be set as specified
on the Track Edit page.
5. Use To: Song to select the copy-destination song, use
Track or “Audio Track” to select the copy-destination
track (if you haven’t checked All Tracks, All MIDI
Tracks, or All Audio Tracks), and use Measure to
select the measure at which the copied data will be
inserted.
You can’t copy between MIDI and audio.
6. To execute the Copy Measure operation, press the OK
button. To cancel, press the Cancel button.
2 (4/4)1 (4/4) 5 (3/4)4 (3/4)3 (4/4) 6 (3/4) 7 (4/4)
2 (4/4)1 (4/4) 5 (3/4)4 (3/4)3 (4/4) 6 (3/4) 7 (4/4)
Track 1
(source)
Track 2
(destination)
Example: When you copy measures 5–7 of track 1 to the third measure of track 2,
measures 3–5 of track 2 will be rewritten.
To Next Page
Loading...
Need help?
General
