SEQUENCER mode
544
If the copy-source you specify is a portion of an audio
event that spans several measures, or if the copy-
destination is a portion of an audio event that spans
several measures, a new region will automatically be
created and named when you execute the Copy Measure
command.
Note: The WAVE file itself will not be modified.
Move Measure
This command moves the specified measures to another
location. Existing data at the destination will be pushed back
to make room for the moved data, and the data surrounding
the old location will be moved to fill in the gap.
1. Select “Move Measure” to open the dialog box.
MIDI tracks
Audio Tracks
2. Use From: Track or “Audio Track” to select the move-
source track.
(By default, this will be the Track Select track.)
If All Tracks, All MIDI Tracks, and All Audio Tracks
are unchecked, only data from the selected track will be
moved.
If you check All Tracks, the playback data of all tracks
including the Master Track will be moved.
If you check All MIDI Tracks (when a MIDI Track is
selected), all MIDI tracks will be moved.
If you check All Audio Tracks (when an Audio Track is
selected), all Audio tracks will be moved.
3. Use From Measure and To End of Measure to specify
the region of measures that will be moved.
By default, the range of measures will be set as specified
on the Track Edit page.
4. Use To: Track or “Audio Track” (if you haven’t
checked All Tracks, All MIDI Tracks, or All Audio
Tracks) to select the destination track, and use
Measure to select the starting measure at which the
data will be inserted.
You can’t move between MIDI and audio.
5. To execute the Move Measure command, press the
OK button. To cancel, press the Cancel button.
If you move a portion of an audio event that spans several
measures, or if you move to a portion of an audio event
that spans several measures, a new region will
automatically be created and named when you execute
the Move Measure command.
Note: The WAVE file itself will not be modified.
Create Control Data
This command creates control change, aftertouch, pitch
bend, or tempo data in the specified region of a MIDI track
or the master track.
1. In Track Select, select the MIDI track on which you
wish to perform the Create Control Data command.
If you wish to modify tempo data, select Master Track as
the track. In this case, the step 4 item “Kind” will be set
to “Tempo.”
2. Select “Create Control Data” to open the dialog box.
3. Specify the range into which the control data will be
inserted.
In From Measure and To End of Measure specify the
measures, and in Beat.Tick specify the beat and clock.
(By default, the range of measures will be set as specified
on the Track Edit page.)
4. Set “Kind” to the type of musical data (event) that you
wish to create.
Control change: Control change data will be inserted.
Use “#” to specify the CC number.
After Touch: Aftertouch data will be inserted.
Pitch Bend: Pitch bend data will be inserted.
Tempo : Tempo data will be inserted (if you’ve selected
the master track).
5. In “Start Value,” select the starting value of the
control data. In “End Value,” select the ending value
of the control data.
By default, the “Start Value” will be set to the value of the
existing data at the start location. If you wish to create
control data that changes smoothly from the starting
2 (4/4)1 (4/4) 5 (3/4)4 (3/4)3 (4/4) 6 (3/4) 7 (4/4)
2 (4/4)1 (4/4) 5 (3/4)4 (3/4)3 (4/4) 6 (3/4) 7 (4/4)
Track 1
(source)
Track 2
(destination)
Example: When you copy measures 5–7 of track 1 to the third measure of track 2,
measures 3–5 of track 2 will be rewritten.
To Next Page
Loading...
Need help?
General
