Korg NAUTILUS Series Parameter Guide

878
LFO
LFO Frequency [Hz] [0.02…20.00]
Sets the LFO speed.
WAH
Frequency Bottom [0…100]
Sets the lower limit of the wah center frequency. See
“Frequency Bottom” on page 779.
Frequency Top [0…100]
Sets the upper limit of the wah center frequency. See
“Frequency Bottom” on page 779.
Resonance [+0…+100]
Sets the resonance amount.
Low Pass Filter [Check-box]
Switches the wah low pass filter on and off.
OUTPUT
Pan [L000…C064…R127]
Sets the stereo image.
Wet/Dry [Dry, 1:99…99:1, Wet]
Sets the balance between the effect and the dry input.
Source [Off…Tempo]
Selects a modulation source for Wet/Dry.
Amount [+/–100]
Sets the modulation amount for Wet/Dry.
Chorus/Flanger
Pre EQ
Trim [0…100]
Sets the EQ input level.
LEQ Gain [dB] [–15…+15]
Sets the gain of the Low EQ.
HEQ Gain [dB] [–15…+15]
Sets the gain of the High EQ.
LFO
Waveform [Triangle, Sine]
Selects the LFO Waveform.
Frequency [Hz] [0.02…20.00]
Sets the LFO speed.
FLANGER
Delay Time [msec] [0.0…1350.0]
Sets the delay time.
Depth [0…100]
Sets the depth of LFO modulation.
Feedback [+/–100]
Sets the feedback amount. See “Feedback” on page 806.
OUTPUT
Pan [L000…C064…R127]
Sets the stereo image.
Wet/Dry [Dry, 1:99…99:1, Wet]
Sets the balance between the effect and the dry input.
Source [Off…Tempo]
Selects a modulation source for Wet/Dry.
Amount [+/–100]
Sets the modulation amount for Wet/Dry.
Phaser
LFO
Waveform [Triangle, Sine]
Selects the LFO Waveform.
Frequency [Hz] [0.02…20.00]
Sets the LFO speed.
PHASER
Manual [0…100]
Sets the frequency to which the effect is applied.
Depth [0…100]
Sets the depth of LFO modulation.
Resonance [+/–100]
Sets the resonance amount. See “Resonance” on page 808.
OUTPUT
Pan [L000…C064…R127]
Sets the stereo image.
Wet/Dry [Dry, 1:99…99:1, Wet]
Sets the balance between the effect and the dry input.
Source [Off…Tempo]
Selects a modulation source for Wet/Dry.
Amount [+/–100]
Sets the modulation amount for Wet/Dry.
Multi-tap BPM Delay
MT DELAY
BPM [MIDI, 40.00…300.00]
MIDI syncs to the system tempo; 40-240 sets the tempo
manually for this individual effect. See “BPM” on page 825.
Time Over? > [---, OVER!]
Displays an error message when the delay time exceeds the
upper limit. See “Time Over? R >” on page 847.
Tap1 Base Note [ …  ]
Selects the type of notes to specify the delay time for Tap1.
See “Base Note” on page 825.

Korg NAUTILUS Series Specifications

General

Sampling	Open Sampling System
MIDI	In, Out, Thru
Preset Combinations	384
Keyboard	61-key (NAUTILUS 61), 73-key (NAUTILUS 73), 88-key (NAUTILUS 88, RH3 weighted action)
Effects	12 Insert Effects; 2 Master Effects; 2 Total Effects
Sequencer	16-track MIDI Sequencer
Storage	Internal SSD (60 GB)
Audio Inputs	2 x 1/4"
Audio Outputs	Headphones
USB	Type A (host), Type B (device)
Weight	NAUTILUS 88: 23.1 kg
Display	8 inch TouchView™ GUI (800x600 pixels)