R&S ZNB - Page 1189

Command Reference
R&S
®
ZNB/ZNBT
1189User Manual 1173.9163.02 ─ 55
[SENSe<Ch>:]FREQuency:CONVersion:ARBitrary:PMETer<Pmtr>................................... 1191
[SENSe<Ch>:]FREQuency:CONVersion:GAIN:LMCorrection............................................1192
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:FIXed<Stg>............................................. 1193
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:FUNDamental..........................................1193
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:IFPort..................................................... 1194
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:LOMultiplier<Stg>.................................... 1194
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:LOPort<Stg>........................................... 1194
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:MFFixed..................................................1195
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:RFMultiplier............................................. 1196
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:RFPort.................................................... 1197
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:STAGes.................................................. 1197
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:TFRequency<Stg>................................... 1197
[SENSe<Ch>:]FREQuency:IMODulation:CONVersion......................................................1198
[SENSe<Ch>:]FREQuency:IMODulation:LTONe..............................................................1198
[SENSe<Ch>:]FREQuency:IMODulation:ORDer<Im>[:STATe].......................................... 1199
[SENSe<Ch>:]FREQuency:IMODulation:RECeiver..........................................................1199
[SENSe<Ch>:]FREQuency:IMODulation:SPECtrum:MORDer...........................................1200
[SENSe<Ch>:]FREQuency:IMODulation:SPECtrum[:STATe]............................................ 1200
[SENSe<Ch>:]FREQuency:IMODulation:TDIStance........................................................ 1201
[SENSe<Ch>:]FREQuency:IMODulation:UTONe.............................................................1202
[SENSe<Ch>:]FREQuency:SBANd................................................................................1202
[SENSe<Ch>:]FREQuency:SEGMent:AXIS.................................................................... 1203
[SENSe<Ch>:]FREQuency:SPAN..................................................................................1204
[SENSe<Ch>:]FREQuency:STARt................................................................................. 1204
[SENSe<Ch>:]FREQuency:STOP..................................................................................1204
[SENSe<Ch>:]FREQuency[:CW] <FixedFreq>
[SENSe<Ch>:]FREQuency:FIXed <FixedFreq>
Defines the fixed (Continuous Wave, CW) frequency for all sweep types operating at
fixed frequency ("Power", "Time", "CW Mode"). The two command forms
[SENSe<Ch>:]FREQuency[:CW] and [SENSe<Ch>:]FREQuency:FIXed are
equivalent.
This command also defines the center frequency of the intermodulation spectrum dia-
gram (option R&S ZNB/ZNBT-K14). The frequency range depends on the R&S ZNB/
ZNBT model; see Chapter 8.3.14.11, "[SENSe:]FREQuency...", on page 1188.
Note:[SENSe<Ch>:]FREQuency[:CW]|:FIXed is equivalent to
SOURce<Ch>:FREQuency<PhyPt>[:CW]|:FIXed. Source and receiver frequency
are always equal; the four commands overwrite each other.
With option R&S ZNB/ZNBT-K4, Frequency Conversion Measurements, port-specific
source and receiver frequencies can be defined; see SOURce<Ch>:
FREQuency<PhyPt>:CONVersion:ARBitrary:IFRequency.
Suffix:
<Ch>
.
Channel number
SCPI Command Reference