R&S ZNB - 8.3.1.18 CALCulate:STATistics...

Command Reference
R&S
®
ZNB/ZNBT
916User Manual 1173.9163.02 ─ 55
Example:
*RST; :CALC:SMO ON
Activate smoothing for the default trace.
CALC:SMO:APER 0.5
Reduce the smoothing aperture to 0.5 %.
Manual operation: See "Aperture" on page 331
8.3.1.18 CALCulate:STATistics...
The CALCulate:STATistics... commands evaluate and display statistical and
phase information of the trace.
CALCulate<Chn>:STATistics[:STATe]............................................................................... 916
CALCulate<Chn>:STATistics[:STATe]:AREA..................................................................... 917
CALCulate<Chn>:STATistics:DOMain:USER.................................................................... 917
CALCulate<Chn>:STATistics:DOMain:USER:SHOW......................................................... 918
CALCulate<Chn>:STATistics:DOMain:USER:STARt.......................................................... 918
CALCulate<Chn>:STATistics:DOMain:USER:STOP...........................................................918
CALCulate<Chn>:STATistics:EPDelay[:STATe]..................................................................919
CALCulate<Chn>:STATistics:MMPTpeak[:STATe]..............................................................919
CALCulate<Chn>:STATistics:MSTDdev[:STATe]................................................................919
CALCulate<Chn>:STATistics:FORMat..............................................................................919
CALCulate<Chn>:STATistics:NLINear:COMP:LEVel.......................................................... 919
CALCulate<Chn>:STATistics:NLINear:COMP:PHASe........................................................920
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER.......................................... 920
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:SHOW................................920
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:STARt................................ 921
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:STOP.................................921
CALCulate<Chn>:STATistics:NLINear:COMP:REFerence.................................................. 921
CALCulate<Chn>:STATistics:NLINear:COMP:RESult?.......................................................922
CALCulate<Chn>:STATistics:NLINear:COMP:RLEVel........................................................922
CALCulate<Chn>:STATistics:NLINear:COMP:RMARker.....................................................923
CALCulate<Chn>:STATistics:NLINear:COMP:RPHase.......................................................923
CALCulate<Chn>:STATistics:NLINear:COMP:RPHase.......................................................923
CALCulate<Chn>:STATistics:NLINear:COMP[:STATe]........................................................924
CALCulate<Chn>:STATistics:RESult?.............................................................................. 924
CALCulate<Chn>:STATistics:RMS[:STATe]....................................................................... 925
CALCulate<Chn>:STATistics:SFLatness[:STATe]...............................................................925
CALCulate<Chn>:STATistics[:STATe] <Boolean>
Displays or hides all statistical results in the diagram area of trace no. <Chn> except
the compression point results.
Tip: You can display or hide the "Min/Max/Peak-Peak", "Mean/Std Dev/RMS",
"Phase/El Length" and "Flatness/Gain/Slope" results separately; see example below.
Suffix:
<Chn>
.
Channel number used to identify the active trace
SCPI Command Reference