R&S ZNB - SOURce:POWer:CORRection...

Command Reference
R&S
®
ZNB/ZNBT
1269User Manual 1173.9163.02 ─ 55
Port-specific and general settings
The SOURce:POWer... subsystem comprises port-specific and general settings.
Port-specific settings are valid for the port specified by the numeric suffix <PhyPt>
(...:POWer<PhyPt>:...). General settings are valid for all test ports of the ana-
lyzer; the port suffix is ignored. Refer to the description of the individual commands for
more information.
SOURce:POWer:CORRection...
The SOURce:POWer:CORRection... commands control a scalar source power cali-
bration.
SOURce:POWer:CORRection:PMETer:ID...................................................................... 1269
SOURce<Ch>:POWer:CORRection:DATA...................................................................... 1270
SOURce<Ch>:POWer:CORRection:DATA:PORT<PhyPt>................................................1270
SOURce<Ch>:POWer:CORRection:DATA:PARameter<Wv>?.......................................... 1271
SOURce<Ch>:POWer:CORRection:IMODulation:PORT.................................................. 1272
SOURce<Ch>:POWer<PhyPt>:CORRection[:ACQuire]................................................... 1273
SOURce<Ch>:POWer<PhyPt>:CORRection[:ACQuire]:VERification:RESult?.................... 1274
SOURce<Ch>:POWer<PhyPt>:CORRection:COLLect:AVERage[:COUNt].........................1275
SOURce<Ch>:POWer<PhyPt>:CORRection:COLLect:AVERage:NTOLerance...................1275
SOURce<Ch>:POWer<PhyPt>:CORRection:COLLect:CFACtor........................................1276
SOURce<Ch>:POWer<PhyPt>:CORRection:COLLect:FLATness..................................... 1276
SOURce<Ch>:POWer<PhyPt>:CORRection:COLLect:METHod....................................... 1277
SOURce<Ch>:POWer<PhyPt>:CORRection:COLLect:RRECeiver....................................1278
SOURce<Ch>:POWer<PhyPt>:CORRection:DATA:PARameter<Wv>:COUNt?...................1278
SOURce<Ch>:POWer<PhyPt>:CORRection:GENerator<Gen>[:STATe]............................ 1279
SOURce<Ch>:POWer<PhyPt>:CORRection:IMODulation:LTONe[:ACQuire]......................1279
SOURce<Ch>:POWer<PhyPt>:CORRection:IMODulation:UTONe[:ACQuire].....................1280
SOURce<Ch>:POWer<PhyPt>:CORRection:NREadings................................................. 1281
SOURce<Ch>:POWer<PhyPt>:CORRection:OSOurces[:STATe].......................................1281
SOURce<Ch>:POWer<PhyPt>:CORRection:PPOWer.....................................................1281
SOURce<Ch>:POWer<PhyPt>:CORRection:PSELect..................................................... 1282
SOURce<Ch>:POWer<PhyPt>:CORRection:STATe........................................................ 1282
SOURce<Ch>:POWer<PhyPt>:CORRection:TCOefficient[:STATe]....................................1283
SOURce<Ch>:POWer<PhyPt>:CORRection:TCOefficient:CALibration..............................1283
SOURce<Ch>:POWer<PhyPt>:CORRection:TCOefficient:COUNt?...................................1284
SOURce<Ch>:POWer<PhyPt>:CORRection:TCOefficient:DEFine<ListNo>....................... 1285
SOURce<Ch>:POWer<PhyPt>:CORRection:TCOefficient:DELete<ListNo>:ALL................ 1285
SOURce<Ch>:POWer<PhyPt>:CORRection:TCOefficient:DELete<ListNo>[:DUMMy].........1286
SOURce<Ch>:POWer<PhyPt>:CORRection:TCOefficient:FEED...................................... 1286
SOURce<Ch>:POWer<PhyPt>:CORRection:TCOefficient:INSert<ListNo>.........................1287
SOURce:POWer:CORRection:PMETer:ID <PowerMeter>
Selects an external power meter for the scalar source power calibration (flatness cali-
bration).
Note: The command cannot be used unless a power meter is connected via GPIB bus,
USB or LAN interface and configured in the "External Power Meters" dialog.
SCPI Command Reference