R&S ZNB - 8.3.3 CONTrol Commands

Command Reference
R&S
®
ZNB/ZNBT
997User Manual 1173.9163.02 ─ 55
8.3.3 CONTrol Commands
The Control... commands allow you to configure the following interfaces:
●
USER PORT
●
Handler I/O connector (Universal Interface, option R&S ZN-B14 / R&S ZNBT-Z14)
●
RFFE GPIO Interface (option R&S ZN-B15 / R&S ZN-Z15)
CONTrol:AUXiliary:C[:DATA]........................................................................................... 998
CONTrol:GPIO<Port>:SENSe:VOLTage?......................................................................... 999
CONTrol:GPIO<Port>:SENSe:CURRent?.......................................................................1000
CONTrol:GPIO:SENSe:SUMCurrent?............................................................................ 1000
CONTrol<Ch>:GPIO:SENSe:TRIGger............................................................................1001
CONTrol<Ch>:GPIO:TIME............................................................................................ 1001
CONTrol<Ch>:GPIO:VOLTage:OUTPut..........................................................................1001
CONTrol<Ch>:GPIO<Port>[:STATe]............................................................................... 1002
CONTrol<Ch>:GPIO<Port>:RANGe...............................................................................1002
CONTrol<Ch>:GPIO<Port>:SHUNt?.............................................................................. 1003
CONTrol<Ch>:GPIO<Port>:VOLTage[:DEFault].............................................................. 1004
CONTrol:HANDler:A[:DATA].......................................................................................... 1004
CONTrol:HANDler:B[:DATA].......................................................................................... 1004
CONTrol:HANDler:C[:DATA]..........................................................................................1004
CONTrol:HANDler:D[:DATA]..........................................................................................1004
CONTrol:HANDler:E[:DATA].......................................................................................... 1004
CONTrol:HANDler:F[:DATA].......................................................................................... 1004
CONTrol:HANDler:G[:DATA]..........................................................................................1004
CONTrol:HANDler:H[:DATA]..........................................................................................1004
CONTrol:HANDler:A:MODE.......................................................................................... 1005
CONTrol:HANDler:B:MODE.......................................................................................... 1005
CONTrol:HANDler:C:MODE.......................................................................................... 1005
CONTrol:HANDler:D:MODE.......................................................................................... 1005
CONTrol:HANDler[:EXTension]:INDex:STATe..................................................................1005
CONTrol:HANDler[:EXTension]:RTRigger:STATe.............................................................1006
CONTrol:HANDler:INPut?............................................................................................. 1006
CONTrol:HANDler:LOGic..............................................................................................1006
CONTrol:HANDler:OUTPut<Pt>:USER...........................................................................1007
CONTrol:HANDler:OUTPut<Pt>[:DATA]..........................................................................1007
CONTrol:HANDler:PASSfail:LOGic................................................................................ 1008
CONTrol:HANDler:PASSfail:MODE................................................................................1008
CONTrol:HANDler:PASSfail:POLicy............................................................................... 1009
CONTrol:HANDler:PASSfail:SCOPe...............................................................................1009
CONTrol:HANDler:PASSfail:STATus?.............................................................................1010
CONTrol:HANDler:RESet..............................................................................................1010
CONTrol:HANDler:SWEepend.......................................................................................1010
CONTrol<Ch>:RFFE:TEST:OUTPut............................................................................... 1011
CONTrol<Ch>:RFFE:TEST:TIME................................................................................... 1011
CONTrol<Ch>:RFFE:TEST:SENSe:TRIGger...................................................................1011
CONTrol<Ch>:RFFE<Bus>:COMMand:DATA................................................................. 1012
CONTrol<Ch>:RFFE<Bus>:COMMand:SEND................................................................ 1012
CONTrol<Ch>:RFFE<Bus>:COMMand:SEND?...............................................................1012
CONTrol<Ch>:RFFE<Bus>:SETTings[:STATe]................................................................ 1013
SCPI Command Reference