R&S ZNB - CALCulate:FMODel:DELT...

Command Reference
R&S
®
ZNB/ZNBT
836User Manual 1173.9163.02 ─ 55
CALCulate:FMODel:DELT...
Commands for Delta-L PCB characterization (see Chapter 5.7.11, "Delta-L 4.0 PCB
Characterization", on page 230).
CALCulate:FMODel:DELT<Ph_pt>:FREQuencies:CURRent?.............................................836
CALCulate:FMODel:DELT<Ph_pt>:FREQuencies:CURRent:COUNt?................................. 837
CALCulate:FMODel:DELT<Ph_pt>:FREQuencies:DEFault?............................................... 837
CALCulate:FMODel:DELT<Ph_pt>:FREQuencies:DEFault:COUNt?....................................837
CALCulate:FMODel:DELT<Ph_pt>:FREQuencies:USEDefault............................................838
CALCulate:FMODel:DELT<Ph_pt>:FREQuencies:USER?..................................................838
CALCulate:FMODel:DELT<Ph_pt>:FREQuencies:USER:COUNt?...................................... 838
CALCulate:FMODel:DELT<Ph_pt>:FREQuencies:USER:ADD............................................839
CALCulate:FMODel:DELT<Ph_pt>:FREQuencies:USER:DELete........................................839
CALCulate:FMODel:DELT<Ph_pt>:FREQuencies:USER:DELete:ALL................................. 839
CALCulate:FMODel:DELT<Ph_pt>:M1L:CACHe:CLEar:ALL...............................................839
CALCulate:FMODel:DELT<Ph_pt>:M1L:CACHe:CLEar:SELected...................................... 840
CALCulate:FMODel:DELT<Ph_pt>:M1L:FILename............................................................840
CALCulate:FMODel:DELT<Ph_pt>:M2L:FILename............................................................840
CALCulate:FMODel:DELT<Ph_pt>:M3L:FILename............................................................840
CALCulate:FMODel:DELT<Ph_pt>:M1L:LENGth...............................................................840
CALCulate:FMODel:DELT<Ph_pt>:M2L:LENGth...............................................................840
CALCulate:FMODel:DELT<Ph_pt>:M3L:LENGth...............................................................840
CALCulate:FMODel:DELT<Ph_pt>:M1L:MEASure............................................................ 841
CALCulate:FMODel:DELT<Ph_pt>:M2L:MEASure............................................................ 841
CALCulate:FMODel:DELT<Ph_pt>:M3L:MEASure............................................................ 841
CALCulate:FMODel:DELT<Ph_pt>:M1L[:STATe]............................................................... 841
CALCulate:FMODel:DELT<Ph_pt>:M2L[:STATe]............................................................... 841
CALCulate:FMODel:DELT<Ph_pt>:M3L[:STATe]............................................................... 841
CALCulate:FMODel:DELT<Ph_pt>:MEASurement............................................................ 841
CALCulate:FMODel:DELT<Ph_pt>:METHod.....................................................................842
CALCulate:FMODel:DELT<Ph_pt>:PORDer..................................................................... 842
CALCulate:FMODel:DELT<Ph_pt>:RUN...........................................................................843
CALCulate:FMODel:DELT<Ph_pt>:SWEep:CONTrol.........................................................843
CALCulate:FMODel:DELT<Ph_pt>:SWEep:CONTrol:IFBW?.............................................. 843
CALCulate:FMODel:DELT<Ph_pt>:SWEep:CONTrol:STEP?..............................................844
CALCulate:FMODel:DELT<Ph_pt>:SWEep:FREQuency:MAXimum.................................... 844
CALCulate:FMODel:DELT<Ph_pt>:SWEep:FREQuency:MINimum..................................... 844
CALCulate:FMODel:DELT<Ph_pt>:TCONfig..................................................................... 844
CALCulate:FMODel:DELT<Ph_pt>:FREQuencies:CURRent?
Returns the frequencies at which the Delta-L algorithm calculates the loss-per-inch
uncertainties.
You can use the algorithms's default or custom frequencies (see CALCulate:
FMODel:DELT<Ph_pt>:FREQuencies:USEDefault).
Suffix:
<Ph_pt>
.
This suffix is ignored
Usage: Query only
SCPI Command Reference