OVERALL MACHINE INFORMATION
B830 72 SM
Sensors
No. Name Description
Full Sensor
S23 Staple Trimmings Hopper
Set Sensor
Detects if the hopper that holds stapling trimmings is set correctly
or incorrectly.
S24 Pre-Stack Stopper HP
Sensor
Detects the pre-stack stopper mechanism at its home position.
S25 Pre-Stack Tray Paper
Sensor (Left)
Detects paper feed in the right side of the pre-stack unit. Controls
the release timing of the pre-stack stopper, and starts the pre-
stack transport motor. Also detects paper jams.
S26 Stapler Tray Entrance
Sensor
Detects a paper jam if there is paper at the entrance of the stapler
unit junction gate when the machine is turned on or after the door
is closed.
S27 Stack Feed-Out Belt HP
Sensor
Detects the home position of the stack feed-out belt.
S28 Staple Tray Full Sensor Detects paper in the stapler tray.
S29 Jogger HP Sensor Detects the home position of the jogger fence in the stapler tray.
S30
Bottom Fence HP Sensor Detects the bottom fence at its home position.
S31
Top Fence HP Sensor Detects the top fence at its home position.
S32 Positioning Roller HP
Sensor
Detects the home position of the positioning roller.
S33 Stack Plate HP Sensor
(Center)
Detects the home position of the center stack plate.
S34 Stack Plate HP Sensor
(Front)
Detects the home position of the front stack plate.
S35 Stack Plate HP Sensor
(Rear)
Detects the home position of the rear stack plate.
S36 Stapler HP Sensor
(Front/Rear)
Detects the home position of the staple unit for side-to-side
movement.
S37 Stapler Rotation Sensor 1 Paired with Stapler Rotation Sensor 2. .This sensor pair controls
the positioning of the corner stapler for the horizontal, 45
o
angle,
and 75
o
angle stapling positions.
S38 Stapler Rotation Sensor 2 Paired with Stapler Rotation Sensor 1 .This sensor pair controls
the positioning of the corner stapler for the horizontal and 45
o
angle stapling positions.
S39 Punch-out Hopper Full
Sensor
Detects when the punch-out hopper is full and detects when the
punch tray is set.
S40 Punch HP Sensor 1 Detects the cam home position for the 2-hole punch. After
punching a sheet of paper, the cam returns to home position and
stops. Home position depends on whether 2 holes or 3 holes are
being made, so there are two punch HP sensors. Punch HP
sensor 1 is used when 2-hole punching is selected, and punch HP
sensor 2 is used when 3-hole punching is selected. When the cut-
out enters the slot of the punch HP in use (sensor 1 or 2-hole
punching) the motor stops.
S41 Punch HP Sensor 2 Detects the cam home position for 3-hole punch. After punching a
sheet of paper, the cam returns to home position and stops. Home
position depends on whether 2 holes or 3 holes are being made,
so there are two punch HP sensors. Punch HP sensor 1 is used
when 2-hole punching is selected, and punch HP sensor 2 is used
when 3-hole punching is selected. When the cut-out enters the
slot of the punch HP in use (sensor 1 or 2-hole punching) the
motor stops.
S42
Shift Tray Jogger HP
Sensor
Detects the actuator on the rear shift tray jogger fence and
switches off the shift tray jogger motor, and signals the machine to
turn on the shift tray jogger retraction motor to raise the fences at
the end of a job.
S43 Shift Tray Jogger
Retraction HP Sensor
Detects the jogger fences of the shift tray jogger unit at their home
positions.
⇒
Rev. 09/2006
To Next Page
Loading...
