Siemens SINAMICS G120D - p20142 MFP 0 run sequence; MFP 0 RunSeq; p20143 BI: MFP 1 input pulse I; MFP 1 inp_pulse I; p20144 MFP 1 pulse duration in ms; MFP 1 pulse_dur ms; r20145 BO: MFP 1 output Q; MFP 1 output Q

List of parameters
Parameters
1-491
© Siemens AG 2012 - 2013 All Rights Reserved
SINAMICS G120D List Manual (LH14), 01/2013
Description: Setting parameter for the run sequence of instance MFP 0 within the run-time group set in p20141.
Note: The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
Description: Sets the signal source for the input pulse I of instance MFP 1 of the pulse generator.
Description: Setting parameter for pulse duration T in milliseconds of instance MFP 1 of the pulse generator.
Description: Display parameter for output pulse Q of instance MFP 1 of the pulse generator.
Description: Setting parameter for the run-time group in which the instance MFP 1 of the pulse generator is to be called.
Value: 5: Run-time group 5
6: Run-time group 6
9999: Do not calculate
p20142 MFP 0 run sequence / MFP 0 RunSeq
CU240D-2_DP
CU240D-2_DP_F
CU240D-2_PN
CU240D-2_PN_F
Access level: 3 Calculated: - Data type: Unsigned16
Can be changed: T Scaling: - Dyn. index: -
Units group: - Unit selection: - Func. diagram: 7230
Min Max Factory setting
0 32000 370
p20143 BI: MFP 1 input pulse I / MFP 1 inp_pulse I
CU240D-2_DP
CU240D-2_DP_F
CU240D-2_PN
CU240D-2_PN_F
Access level: 3 Calculated: - Data type: U32 / Binary
Can be changed: T Scaling: - Dyn. index: -
Units group: - Unit selection: - Func. diagram: 7230
Min Max Factory setting
- - 0
p20144 MFP 1 pulse duration in ms / MFP 1 pulse_dur ms
CU240D-2_DP
CU240D-2_DP_F
CU240D-2_PN
CU240D-2_PN_F
Access level: 3 Calculated: - Data type: FloatingPoint32
Can be changed: T Scaling: - Dyn. index: -
Units group: - Unit selection: - Func. diagram: 7230
Min Max Factory setting
0.00 5400000.00 0.00
r20145 BO: MFP 1 output Q / MFP 1 output Q
CU240D-2_DP
CU240D-2_DP_F
CU240D-2_PN
CU240D-2_PN_F
Access level: 3 Calculated: - Data type: Unsigned32
Can be changed: - Scaling: - Dyn. index: -
Units group: - Unit selection: - Func. diagram: 7230
Min Max Factory setting
- - -
p20146 MFP 1 run-time group / MFP 1 RTG
CU240D-2_DP
CU240D-2_DP_F
CU240D-2_PN
CU240D-2_PN_F
Access level: 3 Calculated: - Data type: Integer16
Can be changed: T Scaling: - Dyn. index: -
Units group: - Unit selection: - Func. diagram: 7230
Min Max Factory setting
5 9999 9999