Siemens SINAMICS G120D - G; I; J; L

Index
C-906
© Siemens AG 2012 - 2013 All Rights Reserved
SINAMICS G120D List Manual (LH14), 01/2013
Simple ramp-function generator, 2-663
Skip frequency bands andspeed limita-
tions, 2-662
Function diagrams, signals and monitoring
functions
Overview, 2-745
Function diagrams, signals and monitoring
functions
Load monitoring, 2-749
Monitoring functions 1, 2-753
Monitoring functions 2, 2-754
Speed messages 1, 2-746
Speed messages 2, 2-747
Thermal monitoring, motor, 2-751
Thermal monitoring, power unit, 2-750
Thermal motor models, 2-752
Torque signals, motor locked/stalled,
2-748
Function diagrams, technology controller
Control modes, 2-743
Fixed values, binary selection
(p2216 = 2), 2-740
Fixed values, direct selection (p2216 = 1),
2-741
Motorized potentiometer, 2-742
Function diagrams, vector control
Current setpoint filter, 2-706
Current/power/torque limits
, 2-705
Display signals, 2-714
Field weakening characteristic, Id setpoint
(ASM, p0300 = 1), 2-709
Field weakening controller (PEM,
p0300 = 2xx), 2-711
Field weakening controller, flux controller
(ASM, p0300 = 1), 2-710
Flux controller configuration, 2-703
Id setpoint (PEM, p0300 = 2), 2-708
Interface to the Power Module
(ASM, p0300 = 1), 2-712
Interface to the Power Module
(PEM, p0300 = 2xx), 2-713
Iq and Id controller, 2-707
Kp_n/Tn_n adaptation, 2-698
Pre-control balancing, acceleration mod-
el, 2-696
Resonance damping and slip-
compensation (V/f), 2-701
Speed control configuration, 2-702
Speed controller, 2-697
Speed setpoint, droop, 2-695
Torque setpoint, 2-699
Upper/lower torque limit, 2-704
V/f characteristic and voltage boost, 2-700
Fxxxx, 3-772
G
General information
about function diagrams, 2-578
about parameters, 1-8
on faults and alarms, 3-768
I
IASC, 3-770
Index
Parameter, 1-9
Index (parameters), 1-17
Internal control words, 2-613
Internal control/status words, 2-613
J
Jogging, 2-655, 2-660
L
Linked parameters, 1-9
List
Abbreviations, B-893
ASCII table, A-892
Binector inputs (BI parameters), 1-552
Binector outputs (BO parameters), 1-558
Command data sets, 1-541
Connector inputs (CI parameters), 1-556
Connector outputs (CO parameters),
1-560
Connector/binector outputs (CO/BO pa-
rameters), 1-565
Drive Data Sets, 1-544
Encoder data sets, 1-551
Fault and alarm messages, 3-777
Message ranges, 3-777
Motor data sets, 1-549
Parameter ranges, 1-19
Parameters for quick commissioning,
1-569
Parameters for write protection and know-
how protection, 1-567
Parameters, all, 1-22
Power unit data sets, 1-551
List of abbreviations, B-893
Load monitoring, 2-744
M
Manufacturer-specific telegrams, 2-599
Message buffer, 2-755
Messages, 2-744
Monitoring functions, 2-744
Motorized potentiometer, 2-655, 2-742