Parameters
BICO parameters (connectors/binectors)
1-554
© Siemens AG 2012 - 2013 All Rights Reserved
SINAMICS G120D List Manual (LH14), 01/2013
p2626 BI: EPOS traversing block selection bit 1 / Trav_blk sel bit 1
p2627 BI: EPOS traversing block selection bit 2 / Trav_blk sel bit 2
p2628 BI: EPOS traversing block selection bit 3 / Trav_blk sel bit 3
p2631 BI: EPOS activate traversing task (0 -> 1) / Trav_task act
p2633 BI: EPOS external block change (0 -> 1) / Ext BlckChg (0->1)
p2637 BI: EPOS fixed stop reached / Fixed stop reached
p2638 BI: EPOS fixed stop outside the monitoring window / Fixed stop outside
p2639 BI: EPOS torque limit reached / M_limit reached
p2640 BI: EPOS intermediate stop (0 signal) / Intermediate stop
p2641 BI: EPOS reject traversing task (0 signal) / Trav_task reject
p2647 BI: EPOS direct setpoint input/MDI selection / MDI selection
p2648 BI: EPOS direct setpoint input/MDI positioning type / MDI pos_type
p2649 BI: EPOS direct setpoint input/MDI transfer type selection / MDI trans_type sel
p2650 BI: EPOS direct setpoint input/MDI setpoint acceptance edge / MDI setp_accept
p2651 BI: EPOS direct setpoint input/MDI direction selection, positive / MDI dir_sel pos
p2652 BI: EPOS direct setpoint input/MDI direction selection negative / MDI dir_sel neg
p2653 BI: EPOS direct setpoint input/MDI setting-up selection / MDI setting-up sel
p2655[0...1] BI: EPOS select tracking mode / Sel tracking mode
p2656 BI: EPOS enable basic positioner / EPOS enable
p2658 BI: EPOS pos. actual value valid feedback signal / Pos valid feedback
p2659 BI: EPOS referencing active feedback signal / Ref act fdbk
p2661 BI: EPOS measured value valid feedback signal / MeasVal valid fdbk
p2662 BI: EPOS adjustment value valid feedback signal / Adj val valid FS
p2663 BI: EPOS clamping active feedback signal / Clamping active FS
p2730[0...3] BI: LR pos. actual value preprocessing activate neg. corr. (edge) / ActV_prep neg corr
p2731 BI: LR reduce I component / Reduce I comp
p3111[0...n] BI: External fault 3 enable / Ext fault 3 enab
p3112[0...n] BI: External fault 3 enable negated / Ext flt 3 enab neg
p3232[0...n] BI: Load monitoring failure detection / Load_moni fail_det
p4655[0...2] BI: XIST1_ERW reset signal source / XIST1_ERW resS_src
p5614 BI: Pe set switch-on inhibit signal source / Pe sw on_inh s_src
p9705 BI: SI Motion: Test stop signal source / SI Mtn test stop
p10007 BI: SI forced checking procedure F-DO signal source / SI FCP F-DO s_src
p20030[0...3] BI: AND 0 inputs / AND 0 inputs
p20034[0...3] BI: AND 1 inputs / AND 1 inputs
p20038[0...3] BI: AND 2 inputs / AND 2 inputs
p20042[0...3] BI: AND 3 inputs / AND 3 inputs
p20046[0...3] BI: OR 0 inputs / OR 0 inputs
p20050[0...3] BI: OR 1 inputs / OR 1 inputs
p20054[0...3] BI: OR 2 inputs / OR 2 inputs
p20058[0...3] BI: OR 3 inputs / OR 3 inputs
p20062[0...3] BI: XOR 0 inputs / XOR 0 inputs
p20066[0...3] BI: XOR 1 inputs / XOR 1 inputs
p20070[0...3] BI: XOR 2 inputs / XOR 2 inputs
p20074[0...3] BI: XOR 3 inputs / XOR 3 inputs
p20078 BI: NOT 0 input I / NOT 0 input I
p20082 BI: NOT 1 input I / NOT 1 input I
p20086 BI: NOT 2 input I / NOT 2 input I
p20090 BI: NOT 3 input I / NOT 3 input I
p20138 BI: MFP 0 input pulse I / MFP 0 inp_pulse I
p20143 BI: MFP 1 input pulse I / MFP 1 inp_pulse I
p20148 BI: PCL 0 input pulse I / PCL 0 inp_pulse I
p20153 BI: PCL 1 input pulse I / PCL 1 inp_pulse I
To Next Page
Loading...
