BICO parameters (connectors/binectors)
Parameters
1-557
© Siemens AG 2012 - 2013 All Rights Reserved
SINAMICS G120D List Manual (LH14), 01/2013
p2299[0...n] CI: Technology controller limit offset / Tech_ctrl lim offs
p2513[0...3] CI: LR Position actual value preprocessing corrective value / Act val_prep corr
p2515[0...3] CI: LR position actual setting setting value / s_act set setVal
p2516[0...3] CI: LR position offset / Position offset
p2530 CI: LR position setpoint / s_set
p2531 CI: LR velocity setpoint / v_set
p2532 CI: LR position actual value / s_act
p2537 CI: LR position controller adaptation / Adaptation
p2541 CI: LR position controller output speed limit signal source / LR_outp lim S_src
p2555 CI: LR LU/revolution LU/mm / LU/rev LU/mm
p2578 CI: EPOS software limit switch minus signal source / SW limSw Min S_src
p2579 CI: EPOS software limit switch plus signal source / SW limSwPlus S_src
p2593 CI: EPOS LU/revolution LU/mm / LU/rev LU/mm
p2594[0...2] CI: EPOS Maximum velocity externally limited / v_Max ext lim
p2598[0...3] CI: EPOS reference point coordinate signal source / Ref_pt coord S_src
p2642 CI: EPOS direct setpoint input/MDI position setpoint / MDI s_set
p2643 CI: EPOS direct setpoint input/MDI velocity setpoint / MDI v_set
p2644 CI: EPOS direct setpoint input/MDI acceleration override / MDI a_over
p2645 CI: EPOS direct setpoint input/MDI deceleration override / MDI -a_over
p2646 CI: EPOS velocity override / v_over
p2654 CI: EPOS direct setpoint input/MDI mode adaptation / MDI mode adapt
p2657 CI: EPOS position actual value/position setting value / Pos act/set value
p2660 CI: EPOS measured value referencing / Meas val ref
p3230[0...n] CI: Load monitoring speed actual value / Load monit n_act
p20094[0...3] CI: ADD 0 inputs / ADD 0 inputs
p20098[0...3] CI: ADD 1 inputs / ADD 1 inputs
p20102[0...1] CI: SUB 0 inputs / SUB 0 inputs
p20106[0...1] CI: SUB 1 inputs / SUB 1 inputs
p20110[0...3] CI: MUL 0 inputs / MUL 0 inputs
p20114[0...3] CI: MUL 1 inputs / MUL 1 inputs
p20118[0...1] CI: DIV 0 inputs / DIV 0 inputs
p20123[0...1] CI: DIV 1 inputs / DIV 1 inputs
p20128 CI: AVA 0 input X / AVA 0 input X
p20133 CI: AVA 1 input X / AVA 1 input X
p20218[0...1] CI: NSW 0 inputs / NSW 0 inputs
p20223[0...1] CI: NSW 1 inputs / NSW 1 inputs
p20228 CI: LIM 0 input X / LIM 0 input X
p20236 CI: LIM 1 input X / LIM 1 input X
p20244[0...1] CI: PT1 0 inputs / PT1 0 inputs
p20250[0...1] CI: PT1 1 inputs / PT1 1 inputs
p20256[0...1] CI: INT 0 inputs / INT 0 inputs
p20266 CI: LVM 0 input X / LVM 0 input X
p20275 CI: LVM 1 input X / LVM 1 input X
p20284 CI: DIF 0 input X / DIF 0 input X
p20308[0...3] CI: ADD 2 inputs / ADD 2 inputs
p20312[0...1] CI: NCM 0 inputs / NCM 0 inputs
p20318[0...1] CI: NCM 1 inputs / NCM 1 inputs
p20372 CI: PLI 0 input X / PLI 0 input X
p20378 CI: PLI 1 input X / PLI 1 input X
To Next Page
Loading...
