EasyManuals Logo

Korg NAUTILUS Series Parameter Guide

Korg NAUTILUS Series
961 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #608 background imageLoading...
Page #608 background image
SAMPLING mode
598
1…4: The signal will be output in monaural to the selected
AUDIO OUTPUT (INDIVIDUAL).
1/2…3/4: The signal will be panned by the “Pan (CC#8)”
setting and sent in stereo to the selected AUDIO OUTPUT
(INDIVIDUAL) pair.
Off: The signal will not be sent directly to the L/R or
Individual buses. Use this setting if you want to apply Send1
and Send2 and then send the signal directly to the master
effects.
FX Control Bus [Off, 1, 2]
Sends the post-IFX signal to the FX Control buses. See “8–
1d: REC Bus” on page 596.
REC Bus [Off, 1…4, 1/2, 3/4]
Sends the post-IFX signal to the REC buses. See “8–1d:
REC Bus” on page 596. If you want to resample via the REC
buses, set Source Bus (0–8c) to REC 1/2 or REC 3/4.
Send1 [000…127]
Send2 [000…127]
These adjust the level at which the post-IFX signal is sent to
master effects 1 and 2. This is valid if Bus Select (8–5a) is
set to L/R or Off.
You can use CC#93 to control the Send 1 level, and
CC#91 to control the Send 2 level. The global MIDI
channel specified by MIDI Channel is used for these
messages.
IFX2…12
Here you can specify each insert effect’s effect type, on/off
status, chaining, and mixer settings following the insert
effect. With the exception of Chain to and Chain, the
parameters are the same as for IFX1. See “IFX1” on
page 597.
IFX2: Chain to [IFX3…IFX12]
IFX3: Chain to [IFX4…IFX12]
IFX4: Chain to [IFX5…IFX12]
IFX5: Chain to [IFX6…IFX12]
IFX6: Chain to [IFX7…IFX12]
IFX7: Chain to [IFX8…IFX12]
IFX8: Chain to [IFX9…IFX12]
IFX9: Chain to [IFX10…IFX12]
IFX10: Chain to [IFX11…IFX12]
IFX11: Chain to [(IFX12)]
These specify the chain destination for each insert effect. If
Chain (check box) is on, the insert effect will be connected
in series to the IFX specified by the Chain to setting.
8–5b: Tempo
(Tempo) [040.00…300.00, EXT]
This specifies the tempo. This setting is used for controlling
effects, etc.
v
8–5: Page Menu Commands
Copy Insert Effect p.122
Swap Insert Effect p.122
Insert IFX Slot p.122
Cut IFX Slot p.123
Clean Up IFX Routings p.124
PAGE p.126
•MODE p.126

Table of Contents

Other manuals for Korg NAUTILUS Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Korg NAUTILUS Series and is the answer not in the manual?

Korg NAUTILUS Series Specifications

General IconGeneral
SamplingOpen Sampling System
MIDIIn, Out, Thru
Preset Combinations384
Keyboard61-key (NAUTILUS 61), 73-key (NAUTILUS 73), 88-key (NAUTILUS 88, RH3 weighted action)
Effects12 Insert Effects; 2 Master Effects; 2 Total Effects
Sequencer16-track MIDI Sequencer
StorageInternal SSD (60 GB)
Audio Inputs2 x 1/4"
Audio OutputsHeadphones
USBType A (host), Type B (device)
WeightNAUTILUS 88: 23.1 kg
Display8 inch TouchView™ GUI (800x600 pixels)

Related product manuals