Lantronix SISPM1040 L3 Series User Manual

Lantronix SISPM1040-xxxx-L3 Web User Guide
33856 Rev. A https://www.lantronix.com/ 330
PdelayIntrvl: If useMgmtPdelay is set, port uses this value to decide the Peer delay request packet interval , else
default value is used. Range is -7 to 5.
useMgmtGptpCapIntrvl: Flag to decide the value to be used for gptp capable tlv signalling packet interval.
MgmtGptpCapIntrvl: If useMgmtGptpCapIntrvl is set, port uses this value to decide the gptp capable tlv
signalling packet interval , else default value is used. Range is -24 to 24.
GptpCapableReceiptTimeout: Number of gPTP capable message intervals to wait without receiving from its
neighbor a Signaling message containing a gPTP capable TLV, before determining that its neighbor is no longer
invoking the gPTP protocol.
initialLogGptpCapableMessageInterval: Specifies the gPTP capable message interval when the port is
initialized, and the value the gPTP capable message interval is set to when a gPTP capable TLV is received with
the logGptpCapableMessageInterval field set to 126
uMSCNRR: useMgtSettableComputeNeighborRateRatio - This value determines the source of the value of
computeNeighborRateRatio. 'True' indicates source as 'mgtSettablecomputeNeighborRateRatio'. 'false' indicates
source as initial value or value set by 'LinkDelayIntervalSetting state machine'.
MSCNRR: mgtSettableComputeNeighborRateRatio - This value indicates the input through management
interface whether to compute neighbor rate ratio or not.
uMSCMLD_ : useMgtSettableComputeMeanLinkDelay - This value determines the source of the value of
computeMeanLinkDelay. 'True' indicates source as 'mgtSettableComputeMeanLinkDelay'. Otherwise, Initial value
or value set by LinkDelayInterval State machine is used.
MSCMLD_ : mgtSettableComputeMeanLinkDelay - This value indicates the input through management interface
whether to compute Mean Link Delay or not. //Common Link Delay Service parameters for 802.1AS */
MLDT: meanLinkDelayThresh - The propagation time threshold, above which a port is not considered capable of
participating in the IEEE 802.1AS protocol.
DA: delayAsymmetry - the asymmetry in the propagation delay on the link attached to this port relative to the
grandmaster time base, as defined in 8.3. If propagation delay asymmetry is not modeled, then delayAsymmetry
is zero.
iLPDRv: initialLogPdelayReqInterval - this value is the logarithm to base 2 of the Pdelay_Req message
transmission interval used.
uMSLPDRv: useMgtSettableLogPdelayReqInterval - This value determines the source of
'currentLogPdelayReqInterval'. 'True' indicates source as 'mgtSettableLogPdelayReqInterval'. Otherwise, initial
value or value set by LinkDelayInterval State machine is used.
MSLPDRv: mgtSettableLogPdelayReqInterval - This value is used if useMgtSettableLogPdelayReqInterval is
true.
iCNRR: initialComputeNeighborRateRatio - Initial value that indicates whether neighborRateRatio is to be
computed by this port.
cm_uMSCNRR: useMgtSettableComputeNeighborRateRatio - This value determines the source of the value of
computeNeighborRateRatio. 'True' indicates source as 'mgtSettablecomputeNeighborRateRatio'. Otherwise, initial
value or value set by LinkDelayInterval state machine is used.
cm_MSCNRR: mgtSettableComputeNeighborRateRatio - This value indicates the input through management
interface whether to compute neighbor rate ratio or not.
iCMLD: initialComputeMeanLinkDelay - Initial value that indicates whether mean Link delay is computed by this
port or not.

Lantronix SISPM1040 L3 Series Specifications

General

Brand	Lantronix
Model	SISPM1040 L3 Series
Category	Switch
Language	English