9 Programming the Instrument
9.1 List of Supported SCPI Commands
[:SENSe]:CORRection:CSET[1]|2|…|16:RF:PORT
[:SENSe]:CORRection:CSET[1]|2|…|16[:STATe]
[:SENSe]:CORRection:CSET[1]|2|…|16:X:SPACing
[:SENSe]:CORRection:CSET:ALL:DELete
[:SENSe]:CORRection:CSET:ALL[:STATe]
[:SENSe]:CORRection:CSET:GROup[1]|2|…|10:DATA
[:SENSe]:CORRection:CSET:GROup:BReak
[:SENSe]:CORRection:CSET:GROup:COMMent
[:SENSe]:CORRection:CSET:GROup:DELete
[:SENSe]:CORRection:CSET:GROup:DESCription
[:SENSe]:CORRection:CSET:GROup:RELoad
[:SENSe]:CORRection:CSET:GROup[:STATe]
[:SENSe]:CORRection:IMPedance[:INPut][:MAGNitude]
[:SENSe]:CORRection:IQ:I:ATTenuation
[:SENSe]:CORRection:IQ:I:ATTenuation:RATio
[:SENSe]:CORRection:IQ:I:GAIN
[:SENSe]:CORRection:IQ[:I]:SKEW
[:SENSe]:CORRection:IQ:Q:ATTenuation
[:SENSe]:CORRection:IQ:Q:ATTenuation:RATio
[:SENSe]:CORRection:IQ:Q:GAIN
[:SENSe]:CORRection:IQ:Q:GAIN:COUPle
[:SENSe]:CORRection:IQ:Q:SKEW
[:SENSe]:CORRection:MS[:RF]:GAIN
[:SENSe]:CORRection:NOISe:FLOor
[:SENSe]:CORRection:NOISe:FLOor
[:SENSe]:CORRection:NOISe:FLOor
[:SENSe]:CORRection:NOISe:FLOor
[:SENSe]:CORRection:NOISe:FLOor
[:SENSe]:CORRection:NOISe:FLOor:ADAptive
[:SENSe]:CORRection:NOISe:FLOor:ADAptive
[:SENSe]:CORRection:NOISe:FLOor:ADAptive
[:SENSe]:CORRection:NOISe:FLOor:ADAptive
[:SENSe]:CORRection:SA[:RF]:GAIN
[:SENSe]:DDEMod:AVERage:COUNt
[:SENSe]:DDEMod:AVERage[:STATe]
[:SENSe]:DDEMod:AVERage:TCONtrol
[:SENSe]:DDEMod:BANDwidth[:RESolution]
[:SENSe]:DDEMod:CCEVm[:ENABle]
[:SENSe]:DDEMod:EQUalization:RESet
[:SENSe]:DDEMod:FREQuency:SYNThesis[:STATe]
[:SENSe]:DDEMod:IF:GAIN:AUTO[:STATe]
[:SENSe]:DDEMod:IF:GAIN:LEVel
[:SENSe]:DDEMod:IF:GAIN:SELect
[:SENSe]:DDEMod:LO:DITHer[:STATe]
[:SENSe]:DDEMod:LO:MIXMode
[:SENSe]:DDEMod:MCHannel:CHANnel:INFO?
[:SENSe]:DDEMod:MCHannel:IPADdress1|2
[:SENSe]:DDEMod:MCHannel:IPADdress1|2
[:SENSe]:DDEMod:MCHannel:IPADdress1|2:LOCKed
[:SENSe]:DDEMod:OPTimize
2521 Vector Modulation Analyzer Mode User's &Programmer's Reference