R&S ZNB - Page 1447

Annexes
R&S
®
ZNB/ZNBT
1447User Manual 1173.9163.02 ─ 55
ENA Emulation Command R&S ZNB/ZNBT Default Parser Command
MMEMory:LOAD:LIMit <string> MMEMory:LOAD:LIMit
MMEMory:LOAD:SEGMent <string> MMEMory:LOAD:SEGMent
MMEMory:LOAD:[:STATe] <string> MMEMory:LOAD:STATe
MMEMory:MDIRectory <string> MMEMory:MDIRectory
MMEMory:STORe[:STATe] <string> MMEMory:STORe:STATe
MMEMory:STORe:FDATa <string> MMEMory:STORe:TRACe
MMEMory:STORe:LIMit <string> MMEMory:STORe:LIMit
MMEMory:STORe:SEGMent <string> MMEMory:STORe:SEGMent
MMEMory:STORe:SNP:DATA <filename> MMEMory:STORe:TRACe:PORTs
MMEMory:STORe:SNP:TYPE:S1P <numeric> MMEMory:STORe:TRACe:PORTs
MMEMory:STORe:SNP:TYPE:S2P <numeric1>,
<numeric2>
MMEMory:STORe:TRACe:PORTs
MMEMory:STORe:SNP:TYPE:S3P <numeric1>,
<numeric2>, <numeric3>
MMEMory:STORe:TRACe:PORTs
MMEMory:STORe:SNP:TYPE:S4P <numeric3>,
<numeric2>, <numeric3>, <numeric4>
MMEMory:STORe:TRACe:PORTs
MMEMory:STORe:STYPe {STATe|CSTate|DSTate|
CDSTate}
MMEMory:STORe:STATe
Always saves measurement conditions and calibra-
tion state (CSTate), regardless of what you set it to.
SENSe{1...4}:AVERage:CLEar [SENSe<Ch>:]AVERage:CLEar
SENSe{1...4}:AVERage:COUNt <numeric> [SENSe<Ch>:]AVERage:COUNt
SENSe{1...4}:AVERage[:STATe] {ON|OFF|1|0} [SENSe<Ch>:]AVERage[:STATe]
SENSe{1...4}:BWIDth[:RESolution] <bandwidth> [SENSe<Ch>:]BWIDth[:RESolution]
SENSe{1...4}:BWIDth[:RESolution]:SELect NORMal
| HIGH
[SENSe<Ch>:]BWIDth[:RESolution]:SELect
SENSe{1...4}:CORRection:COL-
Lect[:ACQuire]:LOAD <numeric>
SENSe{1...4}:CORRection:COL-
Lect[:ACQuire]:OPEN <numeric>
SENSe{1...4}:CORRection:COL-
Lect[:ACQuire]:SHORt <numeric>
SENSe{1...4}:CORRection:COLLect[:ACQuire]:ISO-
Lation <numeric1>, <numeric2>
SENSe{1...4}:CORRection:COL-
Lect[:ACQuire]:THRU <numeric1>, <numeric2>
[SENSe<Ch>:]CORRection:COLLect[:
ACQuire]:SELected
SENSe{1..4}:CORRection:COLLect:CKIT[:SELect]
<integer>
[SENSe:]CORRection:CKIT:SELect
SENSe{1...4}:CORRection:COLLect:ECAL:ISOLa-
tion[:STATe] {OFF|0}
None (no action)
ENA Emulation Commands