Xerox Phaser 7400 Service Manual

Error Messages and Codes 3-13
Printer error - Contact service; report fault [nnn]” (Continued)
Where [nnn] is one of the codes described below.
188 Motor Driver Board Option tray communications error. 3-149
221 Tray 3 Firmware Error. Firmware error in Tray 3 Flash Memory. 3-150
222 Tray 4 Firmware Error. Firmware error in Tray 4 Flash Memory. 3-150
223 Tray 5 Firmware Error. Firmware error in Tray 5 Flash Memory. 3-150
224 Tray 6 Firmware Error. Firmware error in Tray 6 Flash Memory. 3-150
225 Duplex Unit Firmware Error. Firmware error in Duplex Unit Flash Memory. 3-151
226 Motor Driver Board Firmware Error. Software error in Flash Memory. 3-152
227 Finisher Inverter Firmware Error. Firmware error in Inverter Flash Memory. 3-153
230 CRUM Reader Board not installed or failed. 3-154
231 CRUM Reader Interface Failure. A communication error has occurred between
the Engine Logic Board and CRUM Reader Board.
3-154
232 CRUM Reader Interface Failure. Error detected in the CRUM Reader Board
transmit circuitry.
3-154
233 CRUM Reader Interface Failure. A communications failure has occurred
between the CRUM Antenna and the consumable CRUM.
3-154
234 CRUM Reader has detected five or more RFID devices. 3-154
242 Tray 3 Flash Memory Failure. Hardware error in the Tray 3 Flash Memory device. 3-155
243 Tray 4 Flash Memory Failure. Hardware error in the Tray 4 Flash Memory device. 3-155
244 Tray 5 Flash Memory Failure. Hardware error in the Tray 5 Flash Memory device. 3-155
245 Tray 6 Flash Memory Failure. Hardware error in the Tray 6 Flash Memory device. 3-155
246 Duplex Unit Flash Memory Failure. Hardware error in the Flash Memory device. 3-156
247 Motor Driver Board Flash Memory Failure. Flash Memory device error. 3-157
248 Finisher Inverter Flash Memory Error. Inverter Flash Memory device error. 3-158
910 The Tray 2 Lift Motor has failed. 3-159
911 The Tray 3 Lift Motor has failed. 3-160
912 The Tray 4 Lift Motor has failed. 3-160
913 The Tray 5 Lift Motor has failed. 3-160
914 The Tray 6 Lift Motor has failed. 3-160
917 Error in the Transfer Unit Belt. The Belt Rotation Sensor indicates an error. 3-162
918 The Duplex Unit Fan has failed. 3-163
919 +24 V not available to the Duplex Unit. 3-164
920 Failure in the Yellow Imaging Unit Drum or Motor. 3-165
Error Message Summary (Continued)
Error Control Panel Message Page

Xerox Phaser 7400 Specifications

General

Color	Yes
Print technology	Laser
Maximum resolution	600 x 1200 DPI
Time to first page (black, normal)	12 s
Print speed (black, normal quality, A4/US Letter)	40 ppm
Print speed (color, normal quality, A4/US Letter)	36 ppm
Storage media	HDD
Internal memory	512 MB
Processor model	PowerPC
Maximum internal memory	1 MB
Internal storage capacity	20 GB
Total input capacity	800 sheets
Maximum input capacity	3000 sheets
Paper tray 2 input capacity	350 sheets
Auto document feeder (ADF) input capacity	1650 sheets
Maximum print size	297 x 420 mm
Paper tray media types	Envelopes, Labels, Transparencies
Non-ISO print media sizes	Executive (184 x 267mm), Folio (media size), Letter (media size), Statement (140 x 216mm), Legal (media size)
Maximum ISO A-series paper size	A3
Power requirements	100-240V, 50/60Hz
Networking features	Fast Ethernet
Supported media weight(s)	270 g/m²
Maximum operating temperature range (T-T)	10 - 32 °C
Certification	FCC p.15 A, CE
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	-4 - 140 °F
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	20 - 80 %
Maximum duty cycle	150000 pages per month

Weight and Dimensions

Dimensions (WxDxH)	1438 x 623 x 975 mm