Xerox Phaser 7400 Service Manual

A-12 Phaser 7400 Color Printer Service Manual
Service Diagnostics Menu Map (2/2)
Clutch Tests: Test the functionality of clutches, one component at
a time.
Tray 3 Feed Clutch
Tray 4 Feed Clutch
Tray 5 Feed Clutch
Tray 6 Feed Clutch
Registration Roller A Clutch
Solenoid Tests: Test the functionality of solenoids, one
component at a time.
Reg Shutter Solenoid
Exit Gate Solenoid
Face-Up Gate
Finisher Tests:
Finisher Motors
Feed Motor
Saddle Roller
Bundle Motor Forward
Bundle Motor Reverse
Paddle Motor
Bundle Roller
Shift Motor
Order Motor
Staple Motor
Saddle-stitching Motor
Saddle Transfer Motor
Sliding Motor
Punch Motor
Punch Registration Motor
Inverter Motor A
Inverter Motor B
Finisher Sensor/Switches
Entrance Sensor
Tray Paper Detection Sensor
Tray Paper Level Sensor
Tray Upper-limit Sensor
Tray Lower-limit Sensor
Tray Middle Position Sensor
Stapler Home Position Sensor
Stapler Slide Home Position Sensor
Stapler Connected Signal
Stapler Safety Switch
Stapler Self-Prime Sensor
Covers/Doors/Interlocks
Bookbinding Position Sensor
Alignment Tray Sensor
Punch Timing Sensor
Bookbinding Sensors
Front Alignment Plate Sensor
Rear Alignment Plate Sensor
Exit Belt Home Pos Sensor
Bundle Roller Home Pos Sensor
Paddle Home Position Sensor
Bookbinding Clock Sensor
Tray Lift Motor Clock
Punch Connected Signal
Inverter Input Sensor
Inverter Output Sensor
Inverter Exit Sensor
Inverter Cover Switch
ILS
Inverter Joint Sensor
Inverter CNT2 Signal
Finisher Solenoids
Inverter Separator Solenoid
Inverter Pressure Solenoid
Finisher Clutches
Saddle-stitching Clutch
Inverter Registration Clutch
Adjustments/Calibrations Perform adjustments, calibrations
or operations essential to the performance of the system.
Auto Density Control
Edit Density Data
Execute Density Calibration
Density Calibration Results
ATS 4-Sheet Calibration
Edit Thickness Data
Execute Thickness Calibration
Thickness Calibration Results
NVRAM Access: This menu lets you read and reset selected
NVRAM address locations.
NVRAM Reset
CRU Counter Read
CRU Counter Resets
Reset Toner Counts
Reset IU Counts
Reset Fuser Count
Reset Transfer Belt Count
Save Engine NVRAM
Restore Engine NVRAM
IP Controller Diagnostics: Tests the basic functionality of th
e
Controller Board.
RAM Read/Write Test
Exit: Reboots printer out of diagnostics.
For Authorized Service Personnel Use Only. Service Menu
functions are to be used by Xerox service personnel and
authorized service providers. The printer can be damaged by
improper use of the built-in service tests.

Xerox Phaser 7400 Specifications

General

Color	Yes
Print technology	Laser
Maximum resolution	600 x 1200 DPI
Time to first page (black, normal)	12 s
Print speed (black, normal quality, A4/US Letter)	40 ppm
Print speed (color, normal quality, A4/US Letter)	36 ppm
Storage media	HDD
Internal memory	512 MB
Processor model	PowerPC
Maximum internal memory	1 MB
Internal storage capacity	20 GB
Total input capacity	800 sheets
Maximum input capacity	3000 sheets
Paper tray 2 input capacity	350 sheets
Auto document feeder (ADF) input capacity	1650 sheets
Maximum print size	297 x 420 mm
Paper tray media types	Envelopes, Labels, Transparencies
Non-ISO print media sizes	Executive (184 x 267mm), Folio (media size), Letter (media size), Statement (140 x 216mm), Legal (media size)
Maximum ISO A-series paper size	A3
Power requirements	100-240V, 50/60Hz
Networking features	Fast Ethernet
Supported media weight(s)	270 g/m²
Maximum operating temperature range (T-T)	10 - 32 °C
Certification	FCC p.15 A, CE
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	-4 - 140 °F
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	20 - 80 %
Maximum duty cycle	150000 pages per month

Weight and Dimensions

Dimensions (WxDxH)	1438 x 623 x 975 mm