Cisco Catalyst 4500 Series Command Reference Guide

2-147
Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.4.0SG and IOS 15.1(2)SG)
OL-27596 -01
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches
debug device-sensor
debug device-sensor
To enable debugging for Device Sensor, use the debug device-sensor command in privileged EXEC
mode.
debug device-sensor errors events
Syntax Description
Defaults There are no defaults for this command.
Command Modes Privileged EXEC
Command History
Usage Guidelines Use the debug device-sensor command in conjunction with the debug authentication all command to
troubleshoot scenarios where device sensor cache entries are not being created for the connected devices
Examples The following is sample output from the debug device-sensor events command. The debug output
shows how Cisco Discovery Protocol packets and TLVs are received from the device connected to the
GigabitEthernet 2/1 interface:
Switch# debug device-sensor events
Switch#
*Nov 30 23:58:45.811: DSensor: Received cdp packet from GigabitEthernet2/1:00d0.2bdf.08a5
*Nov 30 23:58:45.811: DSensor: SM returned no or invalid session label for
GigabitEthernet2/1:00d0.2bdf.08a5
*Nov 30 23:58:45.811: DSensor: Updating SM with identity attribute list
cdp-tlv 0 00 01 00 0B 4A 41 45 30 37 34 31 31 50 53 32
cdp-tlv 0 00 03 00 03 32 2F 38
cdp-tlv 0 00 04 00 04 00 00 00 0A
cdp-tlv 0 00 05 00 68 57 53 2D 43 32 39 34 38 20 53 6F 66 74 77 61 72 65
2C 20 56 65 72 73 69 6F 6E 20 4D 63 70 53 57 3A 20 36 2E 34 28 35 2E
30 29 20 4E 6D 70 53 57 3A 20 36 2E 34 28 35 29 0A 43 6F 70 79 72 69 67 68 74 20 28 63 29
20 31 39 39 35 2D 32 30 30 33 20 62 79 20 43 69 73 63 6F 20 53 79 73
74 65 6D 73 2C 20 49 6E 63 2E 0A
cdp-tlv 0 00 06 00 08 57 53 2D 43 32 39 34 38
cdp-tlv 0 00 09 00 00
cdp-tlv 0 00 0A 00 02 00 21
cdp-tlv 0 00 0B 00 01 01
cdp-tlv 0 00 12 00 01 00
cdp-tlv 0 00 13 00 01 00
errors Displays Device Sensor error messages.
events Displays messages for events such as protocol packet arrivals, identity updates, and
release events sent to the session manager.
Release Modification
IOS XE 3.4.0SG and
IOS 15.1(2)SG)
Command introduced on the Catalyst 4500 Series switch.

Cisco Catalyst 4500 Series Specifications

General

Series	Catalyst 4500 Series
Category	Switch
Layer Support	Layer 2, Layer 3
Form Factor	Modular chassis
Stackable	No
Chassis Slots	3, 6, 7, 10
Power Supply Options	AC, DC
Redundancy	Power supply, Supervisor engine
Network Management	Cisco IOS Software CLI, SNMP, Cisco Prime Infrastructure
Features	Security, QoS
Port Density	Up to 384 ports per chassis
Security Features	802.1X, ACLs, DHCP Snooping, Dynamic ARP Inspection, IP Source Guard
Supervisor Engine	8-E